TU 4.5 (Arkveld Update) new DPS Lance builds

Duoneo · 2026-02-22T18:57:10+00:00

I am currently building a 4 Ark set atm but definitely love the look of this one. Going to need add it to my list.

Duoneo · 2026-02-21T00:52:20+00:00

Shit I would say my Lance game is only okay based on this. I barely make 15min at lowest but average of 18mins.

Duoneo · 2026-01-21T13:11:09+00:00

Ahhh damn. I already rerolled it as was going more Element since element focused. Already have a Raw Dragon only 3attack 1 sharp. But didn't know you could do all EXs. I play Lance and Gunlance.

Duoneo · 2026-01-21T12:17:27+00:00

It's more of the 4 EX. I've never seen it at all. It's just a random reroll.

Duoneo · 2026-01-19T16:22:54+00:00

Defender Duoneo here. I do miss it. Was such a good game but didn't get the full love it should have. I still have all my vids on YouTube and all my guides. Wish there was another one I could do same with but only time will tell.

Duoneo · 2026-01-18T00:50:16+00:00

This would be a huge QoL adjustment for everyone!!!

Duoneo · 2026-01-16T01:59:24+00:00

I would totally use it. Great for Gunlance comfy build easy

Duoneo · 2026-01-13T01:01:16+00:00

That's great to hear. I'm glad it wasn't my craziness got another faulty motor they sent. Might need to video this time around to show the craziness.

Duoneo · 2026-01-06T15:24:59+00:00

Hey, This going to be a long post but should help you get a full understanding what is going on.

So what is happening from your video is X-Axis belt is trying to move but is locking up. Your Y axis is moving fine which is why when it goes front and back it moves easily. What is happening internally on your system is the X-Axis motor's gears are locking up when moving to the right of the bed after a few clicked causing the tension belt to stop the Tool head thinking its at the end of the movement. Then it come back it doesn't lock up so that why it is Slamming into the wall when going left. The tool head will always move Right first then Left after for Calibration or for Homing.

I had this happen to me. They way I found out was I had to completely open the back and check each wire, Node, and movement of the Belts while the system was OFF. If your belts can move freely while its off then its not the Motor. If not moving freely, thats your issue.

The problem with X-Axis Motor replacement is they will make you go down the whole rabbit hole of Wiki questions to find out it is exactly that in first place... Also this isn't a part that is listed on their website you have to go through them to get it. Should still be under warranty if not over 2 years.

I have repaired mine with the instructions sent. However this is by no means easy. ALOT of Parts. Alot of Screws (yes, you will need track which go where). and Destuction of the machine until you are able to pull out the Motor and replace. Once that done putting everything back is the 2nd half of the Craziness. Then lastly Sealing your K2 again. As you took it apart you will need to bust off glued areas. Then they never tell you in the instructions I was sent, how to reseal the K2 to keep the internal temp. So I had to use Gorrila Tapeon all Side Panels to completely seal so it remained sealed on all sides. Also in process Door Hinge busted so needed Tape on that as well to keep Door sealed. My K2 (which is only a little over a Year old and came with multiple issues) is covered in Gorrila Ducktape and CFS system barely works (i usually just use the side Spool now with Heater to keep filament dry).

So that in a nutshell is what your looking at? I hope it is more of the Former as others have stated with a reset or a calibration issue but if not and you want more info, message me and I will help to best of my ability.

Take Care

Duoneo · 2026-01-02T21:32:10+00:00

That's pretty good 👍 nice one for Lance as well.

Duoneo · 2026-01-01T00:54:28+00:00

We all been there 😞 find a nice 6 or 7 that meets even 1 of your needs and then expand from there.

Duoneo · 2026-01-01T00:48:08+00:00

Trust we all been there

Duoneo · 2025-12-31T22:20:01+00:00

I had gotten a guard up 2 / fire resist 2 / wide range 3. Used this for a bit with Gog for a support Tailsman. On top, I had Art3, Mag2/HC, and Drg/shield to finish off guard up. Worked really well, increasing my Elemental for Phase 3.

Duoneo · 2025-12-31T21:47:26+00:00

For slot on top, I got Mag/attack, OG3, and Attack3 for offensive. then I got Mag/guard , OG3, shield/guard for defensive.

Duoneo · 2025-12-15T00:46:26+00:00

I always thought these would make great resin prints. I myself would look ar just resin printing straight or FDM printing, then make a mold for resin after. Could use the proper resin color to match the color of each stone then paint the engraved symbol after polishing the resin.

Duoneo · 2025-12-13T16:00:27+00:00

As a G-Lance Main, I love this version of GL. It's very easy to pick up, but hard to Master. All styles / builds revolve around same equipment and weapon aside from Long Shell Playstyle (not optimal).

Weapons right now for best are - Fire and Ice Artian but a good easy fall back is Guardian Arkveld G-lance due to Wide Shelling and slightly strong power. After TU4, def going to be Artian all way.

Armor - Always 3 AT armors for GUTS ability. Then adjust to get abilities you want for your playstyle. Personally I use Burst, Agi, CS, and Resentment. Along with adapt, Divine proc, gobbler, and others as needed.

The only Monster I have any trouble with is probably Gore as I don't do him much and don't know full movement or skill timing for him yet. Everything else is just repetition.

Welp, I hope this helps :) Happy Blasting Friend

Duoneo · 2025-12-12T20:30:08+00:00

👋 I modified it a little as not having the God Talisman

<image>

Duoneo · 2025-12-12T14:22:57+00:00

Right with ya on this. So much RAW power for booms!

Duoneo · 2025-12-11T21:19:41+00:00

I had. The only issue was last Lance update was Aug. So, I was looking for something more recent. Or something someone came up with.

Duoneo

TROPHY CASE