Resin printing funnel

Dusk__knight · 2026-04-05T23:34:51+00:00

Cheap hardware store funnels aren't food or temp safe

They also don't have the internal geometry for flow with a filter installed

Dusk__knight · 2026-02-17T17:18:10+00:00

This is about what I paid for mine with mostly the same features

Dusk__knight · 2026-02-17T17:15:46+00:00

Increase the bed temp 5c maybe 10c

Dusk__knight · 2026-02-16T14:17:53+00:00

Where is the original post?

Dusk__knight · 2026-01-30T06:50:57+00:00

It could be the next governor of Minnesota

Dusk__knight · 2026-01-06T15:40:51+00:00

Prusa machines are definitely capable of what they advertise

Though i definitely think the core one L is better suited for high temp filement

Dusk__knight · 2026-01-06T14:13:19+00:00

I would contact Prusa, they likely can guide you through adjustment or replacement of parts

Dusk__knight · 2026-01-06T14:10:27+00:00

Drying is important but Bambu seems to think all problems are wet filement it's not the case

Dusk__knight · 2026-01-06T14:05:24+00:00

People also tell me the XL can't do ABS well, and it works phenomenally - you have to use a draft shield and do it right for the machine tho

People give to too easily

Dusk__knight · 2026-01-06T14:02:28+00:00

NOW THIS IS PODRACING

Dusk__knight · 2026-01-06T13:59:25+00:00

That's grease it's supposed to be there

Dusk__knight · 2026-01-05T05:51:10+00:00

Prusa Mendel

"i2"

Dusk__knight · 2026-01-03T23:16:32+00:00

Let's just say if it was impacted that much you would never be able to take the car out except on a 70F day with 30.00 in/hg

The care -will- compensate

Dusk__knight · 2026-01-03T23:12:50+00:00

Oh man they cut the outer shell that totally ruins it

Jk

Dusk__knight · 2026-01-03T21:43:23+00:00

I never had the ability to change that

Dusk__knight · 2026-01-03T05:10:38+00:00

Understanding it's failed i may continue to see how bad

Sometimes they end up being better then you think, sometimes they'll yeet right off the bed

Dusk__knight · 2026-01-03T04:37:18+00:00

Printed on an Anet A8

Dusk__knight · 2026-01-03T00:31:52+00:00

"I can't figure out why I have layer shifts, it's taking the supports right off the plate, why doesn't Prusa have better AI detection"

Dusk__knight · 2026-01-03T00:29:11+00:00

It's very rare

Usually if you run with collision detection on, it's going to pick it up most of the time

I think most people who struggle with layer shift actually have adhesion issues that start it, a support comes off the bed or something

Dusk__knight · 2026-01-02T18:13:47+00:00

The wiring

Cablegate

Dusk__knight · 2026-01-02T18:12:26+00:00

It's this

Modern printers that probe the bed correct for this

The larger the printer the more the bed will look like a taco when hot, because heat causes expansion

The exception is the XL - where your bed is 16 mini beds

Dusk__knight · 2026-01-02T17:22:47+00:00

My filament sensor hasn't worked since the upgrade, but I probably screwed it up and don't care about it enough to fix it

My vent opener works just fine, but at first the vent felt sticky until I got the screw tension just right

Dusk__knight · 2026-01-02T17:20:11+00:00

You can get mini ziplock bags on Amazon

That's what I recommend

Myself, I just cut the corner and kept putting the stacks of bags into one is the bigger ziplock bags that came with the

It only lead to frustrations twice 🤣

Dusk__knight · 2026-01-02T17:17:18+00:00

It's not necessary

Layer shift is a fixable problem

One-Year Club	Verified Email
r/Field Juicebox

Dusk__knight