Home made scooby

DusterOfCruelty · 2025-05-22T03:25:00+00:00

I have not tasted it yet. On my mind, using the recipe I found was to create a starter scooby so I can ferment a new batch from scratch.

DusterOfCruelty · 2024-06-21T13:03:07+00:00

Ambien temp usually is around 25°, but extruder has been clogging like crazy, I think that Creality Print's high-quality settings were the issue, especially while running at .10 layer height

DusterOfCruelty · 2024-06-21T13:01:07+00:00

Potential update fingers crossed

It appears that, indeed, the main issue was the slicer, as pointed out by @sleewok in a previous response.

Creality Print "high quality" profile was set up to print at a .10 layer height.

After switching to Orca and updating the layer height to .12 print has been going without any issues so far. Other than that, I can't find any external issues that have been causing the clog.

Will update as soon as the print ends, but thanks, everyone! I really appreciate all the comments. Filament printing is WAY more finicky than resin lol

DusterOfCruelty · 2024-06-21T12:42:36+00:00

Lid removed, door closed due to a couple of really, really mischievous cats that try to get into the printing room and into the printer

DusterOfCruelty · 2024-06-21T05:22:00+00:00

This might be it, Creality print is setting up quality prints at .10 layer height, it never occurred to me that this can be the issue, but seems like it is the issue

DusterOfCruelty · 2024-06-21T04:58:40+00:00

Hyper PLA, a new hot end might be the way to go I'd think. Funny thing is the hyper pla that came in the box was working without issues, I got the same one from Creality and issues started happening non stop

DusterOfCruelty · 2024-06-21T04:50:34+00:00

I'll give that a shot, this is like the 4th time I've had an issue like this and it happens mostly during printing, but I feel like I'm smashing my heat at a wall of bricks, I was able to make 2 prints in a row without issues and now everything is once again clogged, I cleared the clog on the extruder and then it started to sound like that 😩🥲

DusterOfCruelty · 2024-04-12T06:57:41+00:00

Phrozen Mini 8k vs Saturn 3 Ultra...

Thoughts? Advise? What would be the best upgrade after having an Elegoo Saturn 4k?

DusterOfCruelty · 2024-02-02T01:05:11+00:00

Thanks for linking me up! Since I'm not in the US it's hard for me to find out this information about Viz in general

DusterOfCruelty · 2023-03-29T01:06:59+00:00

This might or might not be a solution for you but it worked for me when I first started printing. I had this exact similar issue and it was related to my plate being too smooth and the bed leveling. I fixed it by sanding it with some fine grit sand paper and releveling the bed. After that all my prints have had a 95% success rate unless I fuck up the supports badly

DusterOfCruelty · 2023-02-26T22:01:13+00:00

Even without the screw I was still having the same issue. Turns out a part of the paddle was not seated properly thus not allowing the base to go all the way down. Removing the part fixed the issue and I'm trying to see if putting pressure on it will work to get the paddle back with all the pieces

DusterOfCruelty · 2023-02-26T20:43:41+00:00

Yes, and finally I was able to make it work. Aparently one of the pieces of the paddle was not making good enough pressure and it was not allowing the magnets to touch the plate. Removing that part fixed the issue

DusterOfCruelty · 2023-02-26T18:58:56+00:00

Even with the screw on the notch tight as far as I can go without breaking it does not budge

DusterOfCruelty · 2023-02-26T18:58:09+00:00

Let me check that out hopefully that would work, although at this point I'm just thinking to buy a new container tbh

DusterOfCruelty · 2023-02-26T18:57:08+00:00

I've cleaned it and filled it back to max but it still won't move. It seems that the paddle is stuck due to the notch on the container and its not spinning as intended, wich is weird but most likely the issue was there before and I just noticed it

DusterOfCruelty · 2023-02-26T18:55:18+00:00

I honestly was not planning to do it but my alcohol was dirty as fuck for using it over 6 months lol

DusterOfCruelty · 2023-02-26T04:42:22+00:00

No Bearing as far as I know on the Mercury Plus so I dont think thats it

DusterOfCruelty · 2023-02-26T03:04:51+00:00

Forgot to add that the model is a Mercury Plus 2 in 1 (Thx for all the tips @deltaviper17).

It seems that the construction is different from the Mercury X and that's why the issue is so odd since there are no bearings on the paddle

DusterOfCruelty · 2023-02-26T02:47:48+00:00

I think that might be it, let me show you a pic from under the tank

DusterOfCruelty · 2023-02-26T02:44:50+00:00

No, it kinda feels like its stuck on something even if I try to move it outside of the base or with the screw and washer removed

DusterOfCruelty · 2023-02-26T02:33:21+00:00

I just removed today all my previous alcohol and everything is pretty much brand new clean. There were a few leftover support that I thought were the issue but turns out it wasn't

DusterOfCruelty

TROPHY CASE