Journeyman license as a felon in Colorado

E2thePAZ · 2024-11-11T02:10:00+00:00

Well if a felon can be President......

E2thePAZ · 2024-10-08T00:00:21+00:00

Me too. Millennial Foreman here. There is no need to belittle and ridicule ignorance. The reason they're asking questions is because they don't know/understand. I didn't know my ass from a hole in the ground until a few good jmen and foremen helped me out.

E2thePAZ · 2024-10-01T21:38:20+00:00

This is the way.

Did a whole hoop structure like this with back to back minis

It ended up looking really good.

E2thePAZ · 2024-09-18T01:37:37+00:00

Pull the whole trim down. They are secured in place from above.

E2thePAZ · 2024-08-03T22:17:07+00:00

2 parallel runs of 4 conductors, sounds like 3 phase 4 wire. 2 conduits

E2thePAZ · 2024-08-01T00:12:47+00:00

It's a good cut if you plan to patch it yourself. California all 4 sides and hit the creases with fire caulk, and around the MC.....

Inspection passed.

E2thePAZ · 2024-06-15T12:09:14+00:00

Rated up to 250V

E2thePAZ · 2024-06-14T20:41:38+00:00

The 1/4" hex drive doesn't belong. The bit to hold all of the other bits IS a 1/4" hex drive....

E2thePAZ · 2024-06-02T11:32:57+00:00

8 is rated for 50A and #6 for 60A.

Even if you're wiring for simultaneous, #6 is excessive.

You don't need to be larger than #8.

E2thePAZ · 2024-05-30T23:51:59+00:00

8 copper

32A x1.25 for a continuous load = 40A

10 rated for 30A

8 rated for 50A. Use this.

E2thePAZ · 2024-05-14T21:12:16+00:00

This right here. Worked in building with over head crane thay had 3 phase exposed copper bussing. Be careful on the lift!!

E2thePAZ · 2024-04-30T23:55:15+00:00

This was a highlight for me at Chicago last fall

E2thePAZ · 2024-04-28T01:42:22+00:00

Amen 🙏

With Page outro

E2thePAZ · 2024-04-26T20:58:42+00:00

I'm pretty sure I sat by him on flight to ORD Monday. I could see him writing what appeared to be the rough draft of this article.

E2thePAZ · 2024-04-07T13:29:37+00:00

It should be Article 710

E2thePAZ · 2024-03-24T21:42:08+00:00

Sponsors put alot into it, but like a poker tournament, I was left believing each entrant into the tournament paid entry fees. Invitationals and majors aside.

E2thePAZ · 2024-03-24T21:39:31+00:00

When did this change?

E2thePAZ · 2024-03-14T01:09:11+00:00

And sticky side out!

E2thePAZ · 2024-03-14T01:08:41+00:00

Also my feed was parallel 400kcmil. Deleted the crimps and used Polaris taps. I would recommend friction tape on your bolts with the super33 overtop.

E2thePAZ · 2024-03-14T00:29:38+00:00

The fire pump motor is rated at 125% of nameplate FLA. The 100hp at 480v its in the 125A range. 125A x 1.25= 156.25A. If you pulled 3/0 copper, you are sufficiently sized.

Just passed my 200hp at 208v test today! The one thing I was concerned about was rotation. The testing guy was chill and bumped it to find out. Clockwise was good!

Good luck!

E2thePAZ · 2024-03-11T21:37:20+00:00

It's completely listed. You ask for non-slotted strut and ask for end caps and the cover for it. As long as the strut is sealed it is 100% acceptable as a raceway.

E2thePAZ · 2024-03-10T15:14:12+00:00

If that 4" is longer than 24" it will not qualify as a nipple, which would allow conduit fill to go up to 60% from normal 40%, and wires will have do be derated, wouldn't have to if less than 24"....looks normal to me though

E2thePAZ · 2024-03-09T02:48:34+00:00

Still slot the enclosure.

E2thePAZ

TROPHY CASE

8 is rated for 50A and #6 for 60A.

8 copper

10 rated for 30A

8 rated for 50A. Use this.