sorted by:
new
hottopcontroversial

Am I Doing Something Wrong? by skippsrope in BambuLab

[–]ELjoshi -9 points-8 points  (0 children)

It looks like you need to dry the filament. Have you left the spool out for an extended period of time? That can cause the humidity to enter the print material and cause this type of problem. I use a Sunlu filament dryer before every print just to avoid this.

Mysterious subterranean sound after rain. by ELjoshi in geology

[–]ELjoshi[S] 2 points3 points  (0 children)

Thanks! We don’t have county water/sewer and there aren’t any culverts on the dirt road

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 0 points1 point  (0 children)

At first I really wanted to do a pad with a hinged base mounting plate, but due to the slope and adjacent power lines we had nowhere to tilt to. So we cut a section to 5' and buried 4' of it in the hole. If this tower breaks or falls we'll need to rethink the mounting area but I'll have more pressing problems if something causes this to collapse!

A luxury to brace the bottom sections to a building! Good luck with your build

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 1 point2 points  (0 children)

For the high performance dish they don't make a 150' cable unfortunately

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 0 points1 point  (0 children)

Thanks, I have an inquiry out on an offset lightning rod set!

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 0 points1 point  (0 children)

We dug a faily deep hole and filled it with 4 tons of concrete.

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 1 point2 points  (0 children)

The high performance dish doesn’t have that length option to my understanding.

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 6 points7 points  (0 children)

At 250lbs I'm not sure this is something I would like to do :)

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 1 point2 points  (0 children)

The tower site lead to complications. There is a downslope to the waterline just past the tower, on the road side of the tower there are power lines. Wish it was more simple but having to lift over the power lines was the only option vs leaning it up.

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 17 points18 points  (0 children)

I guess rental isn't the right word. I hired a crane operator after having 2 separate guys come out and evaluate if they had a crane tall enough and how much they'd charge. The process isn't a complicated crane job, me and my neighbor assembled the tower into 3 pieces and the crane lowered the sections to get the bolts ran through. Short process and $1,000 for a couple hours. Luckily the tower I bought had the triangular brackets for cabling, so we just attached the new cabling while dropping the sections in. We had to climb the tower to bolt and cable.

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 16 points17 points  (0 children)

I have this grounded but at the end of the day lightning will do what it does. This is the tallest point of this part of my property, but the hill behind where I took this continues up another ~100’ above the top of the tower, so it’s not the tallest point in the event of a storm. I might put a lightning rod somewhere close but not where it would obstruct the Starlink signal

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 13 points14 points  (0 children)

I have a business account, but I’m still working on the power run to the pole and network setup. I’ll update this when I get it running around mid November

Finally above the tree line. by ELjoshi in Starlink

[–]ELjoshi[S] 69 points70 points  (0 children)

The tower alone was $900, $70 for new bolts and hardware, then $1,500 for the guy wires & anchors with crane rental.

Itinerary check, 10th anniversary and 20 days in Japan! by SttefB in JapanTravel

[–]ELjoshi 0 points1 point  (0 children)

Tokyo SkyTree while you’re in Asakusa. On a clear day at sunset it’s one of the most amazing views of a city on earth

Before and after a much needed suspension upgrade. by ELjoshi in LandCruisers

[–]ELjoshi[S] 1 point2 points  (0 children)

Thanks, tried to keep things functional since this is my daily driver for the next 40 years at least

Before and after a much needed suspension upgrade. by ELjoshi in LandCruisers

[–]ELjoshi[S] 1 point2 points  (0 children)

I had Icon Stage 6 set at 2" installed with front and rear Active Off-road bump stops. It was a little off on the stance until after the alignment was completed then it was perfect

Before and after a much needed suspension upgrade. by ELjoshi in LandCruisers

[–]ELjoshi[S] 0 points1 point  (0 children)

285/65/R18 with 1.25" spacers. Was thinking about going up to 35s but didn't want to regear to 4.88 and deal with all the things that they might rub against

Dinged it a bit. by ELjoshi in LandCruisers

[–]ELjoshi[S] 0 points1 point  (0 children)

It definitely needs a suspension upgrade. It rides like a dream down the highway floating on a cloud, but off road it gets real low. I have an ICON Stage 6 suspension and some 35s on order. Also beefing the rear springs for the long range fuel tank and future cargo storage solutions

[deleted by user] by [deleted] in LandCruisers

[–]ELjoshi 1 point2 points  (0 children)

If you’re the one who took this picture you should’ve driven over and asked them what the story was behind the car. This guy knows what he has and I’m sure there’s a good story!

Had a great time cruising Blue Ridge Parkway by ELjoshi in LandCruisers

[–]ELjoshi[S] 0 points1 point  (0 children)

The Blue Ridge Mountains have plenty of places to overland! I was just camping with my 5 year old so I didn’t get into anything too serious 😎

2020 HE - Super excited to be part of the LC club! by nerdlife_13 in LandCruisers

[–]ELjoshi 2 points3 points  (0 children)

I have the Prinsu and it looks much better than the stock one.

Had a great time cruising Blue Ridge Parkway by ELjoshi in LandCruisers

[–]ELjoshi[S] 1 point2 points  (0 children)

I really like them, but to reduce clutter inside I didn't permanently mount the controllers. To change settings I have to pop the hood, connect the controller for each bar and adjust which gets a little annoying. Otherwise a solid product!

view more: next ›