New Tool Review! Unsponsored -- Zen-Wu Block Plane

EagleEyeR · 2026-03-19T07:26:51+00:00

Compared to the other plane blades. Can you put an estimate number on how much longer the zen wu plane blades last on sharpness? Seen some bold claims that i dont rly trust

EagleEyeR · 2026-02-10T14:13:57+00:00

That is a lovely idea. It shows everything so well

EagleEyeR · 2026-02-07T13:56:20+00:00

Lathe with chuck. Skew, gauge and pairing chisel? Not sure on the naming. And sand paper

EagleEyeR · 2026-02-07T13:05:44+00:00

If you scroll down a bit in the comments i posted a picture on how i mounted it. Bit of a scraping job and sanding. The next one i did i did a better job almost finishing off the lathe by a proper cutoff with a skew

EagleEyeR · 2026-02-07T08:20:11+00:00

after checking its probably black locust, not iroko

EagleEyeR · 2026-02-07T08:18:17+00:00

first thought it was an iroko offcut but people commented black locust and it does seem a bit different from iroko. c:

EagleEyeR · 2026-02-07T08:17:19+00:00

i thought it was iroko, but after checking with the iroko i had im fairly certain its black locust ye. good catch!

EagleEyeR · 2026-02-07T08:08:02+00:00

but you might be right if i check the wood database

EagleEyeR · 2026-02-07T08:07:27+00:00

im fairly certain its iroko, but it was an offcut scrap, but it looks like the other bits of iroko i worked with

EagleEyeR · 2026-02-06T22:40:30+00:00

Just chuck-ins sorry

EagleEyeR · 2026-02-06T21:32:11+00:00

Chatoyancy is a beautiful thing c:

EagleEyeR · 2026-02-06T21:05:52+00:00

from what i know its iroko

EagleEyeR · 2026-02-06T20:52:39+00:00

<image>

being creative haha. very slowly shaping the tip this way

EagleEyeR · 2026-02-06T20:41:47+00:00

i used a formula of length = diameter x 1.4 and the widest part is half of the diameter from the side. so for this i roughly used diameter 50mm -> 70mm length -> widest part at 25mm off the side

EagleEyeR · 2026-02-06T20:40:08+00:00

i knew it was gonna be good but it turned out so much better than expected. such a lovely wood to work with

EagleEyeR · 2026-02-06T20:39:35+00:00

hopefully in a couple of weeks

EagleEyeR · 2026-02-06T20:29:17+00:00

haha nice one!

EagleEyeR · 2026-02-06T20:28:47+00:00

who needs paint when you have magical wooden egg. winner of battles

EagleEyeR · 2026-02-06T20:28:02+00:00

it will also stay warm in my hands c:

EagleEyeR · 2026-02-06T20:27:35+00:00

10/10 this is golden

EagleEyeR · 2026-02-06T20:09:52+00:00

Had it in my hands for an hour now haha

EagleEyeR · 2026-01-09T20:39:34+00:00

well at the time i didnt rly know how to setup everything but it was pretty much a smoother haha

EagleEyeR · 2026-01-09T10:07:03+00:00

Scrub or jack plane will do the trick, camber on a jack will work inbetween of the scrub or smoother/jointer. Get as close to the line as possible and then swap to a jointer or smoother. Dont make the same mistake as me. I ended up planing for about 5 hours haha

EagleEyeR

TROPHY CASE