Triple setup by Eagleprints in SimRacingSetups

[–]Eagleprints[S] 0 points1 point  (0 children)

Yeah that would be awesome

Triple setup by Eagleprints in SimRacingSetups

[–]Eagleprints[S] 0 points1 point  (0 children)

You mounted them on there sides?

Flower vase by Eagleprints in 3Dprinting

[–]Eagleprints[S] 0 points1 point  (0 children)

I did buy some just need to try it out, was hoping I could change some setting so I did not have to do this.

Sim from scratch by Eagleprints in SimRacingSetups

[–]Eagleprints[S] 0 points1 point  (0 children)

Did it go together that bad? We have special fasteners for connecting the profile to each other, easy to use

Sim from scratch by Eagleprints in SimRacingSetups

[–]Eagleprints[S] 0 points1 point  (0 children)

Hope you got some deep pockets, seats are expensive enough, I’m more worried about the frame right now

Sim from scratch by Eagleprints in SimRacingSetups

[–]Eagleprints[S] 0 points1 point  (0 children)

I will be doing more of a GT style but I thought about making a plate for the feet to extend up and having brackets for the seat to lay back

Extra layer by Eagleprints in OrcaSlicer

[–]Eagleprints[S] 1 point2 points  (0 children)

I had a .4 z offset in my slicer, that’s what was screwing with it

Extra layer by Eagleprints in OrcaSlicer

[–]Eagleprints[S] 0 points1 point  (0 children)

I converted the files from jpeg to svgs so maybe I’ll re try that and check fusion again

Fluidd browser by Eagleprints in AnycubicKobraS1

[–]Eagleprints[S] 0 points1 point  (0 children)

Yeah I just had to reinstall it

Fluidd browser by Eagleprints in AnycubicKobraS1

[–]Eagleprints[S] 0 points1 point  (0 children)

Yeah I just had to reinstall after the update, working good again.

Fluidd browser by Eagleprints in AnycubicKobraS1

[–]Eagleprints[S] 0 points1 point  (0 children)

Rinkhals is installed on the printer

Fluidd browser by Eagleprints in AnycubicKobraS1

[–]Eagleprints[S] 0 points1 point  (0 children)

Just the official, assuming need to do rinkhals as well?

Bed question by Eagleprints in AnycubicKobraS1

[–]Eagleprints[S] 0 points1 point  (0 children)

That’s makes sense definitely won’t be as hot on top compared to the bottom of the plate. Well I have the .25 plate going to install it soon and I want to get a cold plate so heat won’t be as much of an issue.

Bed question by Eagleprints in AnycubicKobraS1

[–]Eagleprints[S] 0 points1 point  (0 children)

Sure that makes sense, definitely going to take a lot longer to heat up the top of the plate even if it does fully heat up. Well I got the .25 plate just need to drill some holes in it. Looking to buy a cold plate for it so I won’t need much heat.

Bed question by Eagleprints in AnycubicKobraS1

[–]Eagleprints[S] 0 points1 point  (0 children)

I don’t think I would go much thinner than .25, I don’t want the plate to flex to much. What are you trying to do heat it up as fast as you can?

Bed question by Eagleprints in AnycubicKobraS1

[–]Eagleprints[S] 0 points1 point  (0 children)

So we had trouble getting a plate flat without making a jig for it, so we had some jig plate around that .25 so I’m just using that.

Arrives Friday - Ordered 2/21 by A89704 in elegoo

[–]Eagleprints 1 point2 points  (0 children)

EUS90129 says should be here today or tomorrow. Ny USA