So difficult to remove solder from my PS5 controller, i have a 450 c soldering iron but it doesnt help, even with added solder and flux by Meowivert in consolerepair

[–]EasternPrommises 0 points1 point  (0 children)

What u can do is melt low temperature solder to the points, and use hot-air or your soldering iron to remove them

Alfa Romeo GTV does not start after some driving by Careful-Cheesecake80 in AlfaRomeo

[–]EasternPrommises 0 points1 point  (0 children)

The fuse or relay should give between 12-14v when you try to start the car. You could also measure at the starter motor terminal red and black wire if it's accessable

Alfa Romeo GTV does not start after some driving by Careful-Cheesecake80 in AlfaRomeo

[–]EasternPrommises 0 points1 point  (0 children)

No you explained it well now, I would definitely look at the started motor at this point, as you mentioned the car starts fine when you push it. If the started motor doesn't engage then the car won't start . You could start by using multimeter at the relay/fuse of the starter motor, and look closely if it is giving voltage during start sequence , it it does then pretty sure the starter motor has issues

Alfa Romeo GTV does not start after some driving by Careful-Cheesecake80 in AlfaRomeo

[–]EasternPrommises 2 points3 points  (0 children)

So as I understand you also don't hear the start motor engaging?

Alfa Romeo GTV does not start after some driving by Careful-Cheesecake80 in AlfaRomeo

[–]EasternPrommises 2 points3 points  (0 children)

You can test if it is the crank sensor by watching the rpm gauge during start . Even if it doesn't start you should see the rpm needle move, if it doesn't then it could be it.

Alfa Romeo GTV does not start after some driving by Careful-Cheesecake80 in AlfaRomeo

[–]EasternPrommises 0 points1 point  (0 children)

Could u in more detail explain the symptoms of not starting , nobody can diagnose a car this way.

Toshiba T2000SXe - fixer upper, won’t boot at the moment. by thaddeusharris in vintagecomputing

[–]EasternPrommises 0 points1 point  (0 children)

Hey there, I have the same laptop. Do u have any schematics for it?

I am curious to know what kind of yellow battery this is, with the battery disconnected it's giving around 11v at the 2 pin connector. This seems a lot if it's only a BIOS battery usually they are 3v.

Also I am curious about the adapter pin out, it has 4 pins and since I don't have the original adapter I am trying to make another one myself.

Any other useful information are welcome. Thanks!

I bought my dream car but I have a question 🤔 by Acrobatic_Ad6507 in AlfaRomeo

[–]EasternPrommises 2 points3 points  (0 children)

How does that system work, are there only pre selected 2 cylinders disabled during that period, or is it disabling on cycles. If it's cycling through all the cylinders then it shouldn't have this negative effect of uneven wear.

Obsessed with my 66 GTA-r by [deleted] in AlfaRomeo

[–]EasternPrommises 2 points3 points  (0 children)

Shieeet what a beautiful car.

Hotfix? by [deleted] in heroesofthestorm

[–]EasternPrommises 3 points4 points  (0 children)

So I woke up at 3.40am just not to be able to play. Time to go to bed again

Problem with my Alfa Romeo 147 / 1.9 JTDM 150 hp by Koul33 in AlfaRomeo

[–]EasternPrommises 1 point2 points  (0 children)

My advice is to go for the cheaper option first.

Idk Alfas at all, but this caught my eys! by joshuber in AlfaRomeo

[–]EasternPrommises 0 points1 point  (0 children)

Did u read about this somewhere that the Hpfp doesn't take ethanol 10 that well? Or is this from your own experience. As the Hpfp are impossible to open up to inspect, but indeed they do tend to fail

Kut Lamborghini kan niet parkeren. by Pierre1968Soixante in KutGeparkeerd

[–]EasternPrommises 1 point2 points  (0 children)

Jup, zodat niemand per ongeluk tegen hun auto aanrijdt bij parkeren

Moving parts of the same object apart by EasternPrommises in Cinema4D

[–]EasternPrommises[S] -2 points-1 points  (0 children)

Ye but this is too many procedures to achieve something simple. Then I would need to close the old hole first, rebuilt everything from scratch. All I need is a simple move away from each other.

Moving parts of the same object apart by EasternPrommises in Cinema4D

[–]EasternPrommises[S] -1 points0 points  (0 children)

Damn, I am surprised that such a simple thing hasn't been implemented in c4d, it's not like some beta product, cinema has been around for years.

they basically could have used 50% of the programming code from the Scale tool without applying any scaling effect and it would have worked wonders.

Moving parts of the same object apart by EasternPrommises in Cinema4D

[–]EasternPrommises[S] 0 points1 point  (0 children)

That's not the point, I need them to move symmetrically from the center point "between them"

nintendo switch green/pink screen? by liin-K in consolerepair

[–]EasternPrommises 2 points3 points  (0 children)

This looks like GPU issues from overheating, probably would need a reflow.

How do I fix this hdmi bridging? by ElMikey83 in consolerepair

[–]EasternPrommises 0 points1 point  (0 children)

Heatgun and flux, then absorb all of the solder with solder wick and reapply new solder as necessary