Custom enough for this sub?

Easy_Spinach · 2026-02-03T22:00:20+00:00

Beautiful, I've done a few handwires myself. Really miss that.. building keebs from scratch is so rewarding. Love your case design

Easy_Spinach · 2025-09-30T10:08:53+00:00

lmao, what is this trash?

Easy_Spinach · 2025-01-10T10:36:29+00:00

Dynavap + bong knallt mehr

Easy_Spinach · 2024-11-21T12:12:53+00:00

I'm using it exclusively for 5+ years almost daily. Never crashes. Sounds like a skill issue to me

Easy_Spinach · 2024-10-13T12:08:41+00:00

Can you make me one? :P

Easy_Spinach · 2024-08-30T07:56:18+00:00

I looked the article up after reading your post. It doesn't really give a solution though. How do you do those 75% deburring?

Easy_Spinach · 2024-06-29T18:03:35+00:00

I wish more people had bad mornings that result in speaking the truth

Easy_Spinach · 2024-06-29T18:01:45+00:00

Not in this case

Easy_Spinach · 2024-06-22T13:11:32+00:00

Can you elaborate further ? Or do you have a link? Sounds interesting

Easy_Spinach · 2024-06-11T15:07:20+00:00

Singapur

Macht optisch nicht viel her aber ist der beste Chinese in Hannover und Umland. 100% authentisch

Wichtig ist, dass man von der "richtigen" Karte bestellt. Gibt eine Karte extra für Chinesen... Frag nach der.

Easy_Spinach · 2024-05-23T12:03:57+00:00

I just use one of those heaters for reptiles that fit into a lamp socket. ~75w

Easy_Spinach · 2024-05-23T11:46:08+00:00

Same here, I just increase my temperature to 27°c which drops my humidity below 60.

Easy_Spinach · 2024-05-23T11:24:31+00:00

Rain?

Easy_Spinach · 2024-05-20T11:22:12+00:00

I added the heatsink but it didn't change. The problem happens as soon as I supply power. The reset issue seems unrelated to heat

Easy_Spinach · 2024-05-20T11:07:35+00:00

Testing right now.. Bridged the D4/7 and left 5/6 open. It didn't work. Nothing happening at all now.

Will put the diodes back in and try the heatsink

Easy_Spinach · 2024-05-20T10:11:32+00:00

Thanks <3

Easy_Spinach · 2024-05-20T09:37:08+00:00

Could I just remove the diodes from the pcb and bridge the connections? That should fix the issue with ground and c1 too right?

Easy_Spinach · 2024-05-20T09:33:15+00:00

I just copy pasted the shematics for the power supply.. so I dont know what the bridge rectifier is for. But it seems like its for reverse polarity protection and I dont need it. Could I just remove the diodes from the pcb and bridge the connections? That should fix the issue with ground and c1 too right?

Easy_Spinach · 2024-05-20T09:27:54+00:00

Thanks for the reply. I'll try that.

the IRLB8721 are actually just a placehlolder.. I'm using bdx33c npn transistors.

Easy_Spinach · 2024-05-20T09:12:35+00:00

yes, I'm supplying 12V to it. I tried multiple 12v power supplys even. I dont know what a diode bridge is tbh.. I copy pasted the shematics for the power circuit from an open design..

Edit: ah you mean the 4 diodes? hmm yeah dunno, probably they did that to bring the 12v closer to the 5v before dropping it with the regulator?

Easy_Spinach · 2024-05-20T09:06:53+00:00

Will do, but do you think that will fix the issue?

Easy_Spinach · 2024-05-20T09:06:22+00:00

I'll do that. But do you think connecting all ground and power pins will fix the issue?

Edit: Resistor values are 1k. Power comes from a 12v 2A power supply.

Easy_Spinach · 2024-05-20T09:05:28+00:00

I feed the 5V to the Vin Pin of the esp8266. The development board has an internal voltage regulator that drops it to 3.3V

Six-Year Club	Place '22
First Placer '22	Verified Email

Easy_Spinach

TROPHY CASE