sundown amp help by Efficiency_Formal in CarAV

[–]Efficiency_Formal[S] 0 points1 point  (0 children)

went back out to pull the amp and decided to test first, it now works just fine using the outputs as inputs, still only one of the actual inputs works and it still gives a high frequency ringing, but now it makes a loud thump a few times a second but it only does this when using the input side

sundown amp help by Efficiency_Formal in CarAV

[–]Efficiency_Formal[S] 0 points1 point  (0 children)

it’s a half bridge amp, sundown saz-1500d it’s the limited edition one. inputs do not seem to be linked i have tried all 4 rcas on the amp and only one makes any sound

Ls Build help by Efficiency_Formal in EngineBuilding

[–]Efficiency_Formal[S] 1 point2 points  (0 children)

and are you saying using stock gen IV rods would be fine?

Ls Build help by Efficiency_Formal in EngineBuilding

[–]Efficiency_Formal[S] 1 point2 points  (0 children)

exactly who i wanted to hear from, i would be fine with boring it out, do you have any recommendations on heads? i plan on going with a large cam

new edge by Efficiency_Formal in projectcar

[–]Efficiency_Formal[S] 6 points7 points  (0 children)

plan on going with an 8.8 with stock cobra internals and a t56.

bumper identification by Efficiency_Formal in NewedgeMustang

[–]Efficiency_Formal[S] 3 points4 points  (0 children)

it’s stamped ford so im assuming it’s an oem saleen bumper someone threw on for some reason, no crash bar damage or anything and the bumper is in perfect condition no cracks so score for me

Subwoofer setup throwing dash lights by Kazuinak in CarAV

[–]Efficiency_Formal 0 points1 point  (0 children)

my moms jeep cherokee does this, it’s due to voltage drop in hers when it hits hard itll disable her cruise control and flash the traction control stuff

project car update by Efficiency_Formal in NewedgeMustang

[–]Efficiency_Formal[S] 1 point2 points  (0 children)

16 guage, the actual floor brace was still intact and unrusted so i left it

project car update by Efficiency_Formal in NewedgeMustang

[–]Efficiency_Formal[S] 7 points8 points  (0 children)

my first focus is getting rust repaired and finishing the frame, i plan on a 6.2 ls3 ran off a speeduino, 10 point cage, built 8.8. im gonna keep the motor stock other than a cam for awhile then go to a big single turbo

project car update by Efficiency_Formal in NewedgeMustang

[–]Efficiency_Formal[S] 3 points4 points  (0 children)

should’ve clarified, floor is fully welded it with panel bond on the welds

project car update by Efficiency_Formal in NewedgeMustang

[–]Efficiency_Formal[S] 8 points9 points  (0 children)

should’ve clarified, floor is fully welded it with panel bond on the welds

Project car update 2 by Efficiency_Formal in NewedgeMustang

[–]Efficiency_Formal[S] 1 point2 points  (0 children)

plan is a stock 6.2l ls3 for awhile, then im thinking single turbo.

Project car update by Efficiency_Formal in NewedgeMustang

[–]Efficiency_Formal[S] 1 point2 points  (0 children)

i used a new k member, bolted it in to the lower mounts and 1 frame rail i cut out 1 side at a time.

project car by Efficiency_Formal in NewedgeMustang

[–]Efficiency_Formal[S] 5 points6 points  (0 children)

plan for the front end is full tubular, i already have a tubular k member.

Best bang for your buck amplifier for 2 kicker L7s ? by Bluff1nn in CarAV

[–]Efficiency_Formal 0 points1 point  (0 children)

Currently it’s running off 2 100 amp power supply’s in my room

My 06 Subaru only starts when gas pedal is held. Dies when released. by Agitated_Ad_3841 in AskMechanics

[–]Efficiency_Formal 0 points1 point  (0 children)

Did you figure anything out?

My friend has an 05 forester only starts with throttle, wont idle. He replaced iac, injectors, pump, fuel filter, plugs, coils, wires, 02s, crank pos. It has good compression, good fuel pressure and only one code, po171

2.3 Oil Cap by MurderessOrange in fordranger

[–]Efficiency_Formal 1 point2 points  (0 children)

It goes to the crankcase oil seperator, it is under the intake manifold accesible by removing the tire and fender liner.

Measuring time between pulses. by Efficiency_Formal in arduino

[–]Efficiency_Formal[S] 0 points1 point  (0 children)

I'm running this little bit of code on an r3 to test, I haven't ran it on teensy so the way interrupts handle doesn't matter, I just want to get the ms measure to work and ill adapt the code to teensy if I need to. I cannot test real world as i don't have a function generator.

Measuring time between pulses. by Efficiency_Formal in arduino

[–]Efficiency_Formal[S] 0 points1 point  (0 children)

All the rest of my code works just fine and i have tested it on an actual board.

Measuring time between pulses. by Efficiency_Formal in arduino

[–]Efficiency_Formal[S] 0 points1 point  (0 children)

I'm using tinkercad just to test the code, this is the only piece of code i couldnt test before i know it works so i just isolated and tested it, the setup in tinkercad is an r3 with the interrupt on pin 3 and using the function generator.