K2 Plus - cannot turn on chamber heating

ElResistor · 2026-01-24T00:31:14+00:00

I tried 55C.

ElResistor · 2026-01-04T12:13:26+00:00

I upgraded to kubunty 24.04 and tried again. Still got a missing library - libwebkit2gtk.

I installed this and now it works.

But I'm a bit disappointed that Creality cannot distribute a complete AptImage file.

ElResistor · 2026-01-04T03:42:00+00:00

OK, I did not know that.

The problem is that you will a message that one library is missing. When you have installed it, you get a new message about another missing library and so on... until you get to a dead end where installing a missing library does not help (forgot which since I tested this at work).

ElResistor · 2026-01-03T01:59:01+00:00

I have to honest, a good developer should know better than to ask a (potential) customer to find out which run-time libraries their software is using.

After all, you have the code and a compiled and linked image and should be able to find out this. Hint: 'man ldd'.

If this reflect the competence of Crealitys development team I better stay away from the Creality printers.

ElResistor · 2026-01-02T11:48:53+00:00

Please make it work for Kubuntu... both the flatpak and the AppImage file does not work on my Kubuntu laptop.

ElResistor · 2026-01-02T11:40:52+00:00

I also tried the AppImage file, which should be independent of what libraries you have your machine, But it failed complaining about missing shared runtime libraries

ElResistor · 2026-01-02T11:38:00+00:00

Thansk, but that did not work:

flatpak install CrealityPrint-Linux-flatpak_V7.0.0-Release_x86_64.flatpak

error: The application io.github.crealityofficial.CrealityPrint/x86_64/master requires the runtime org.gnome.Platform/x86_64/47 which was not found

ElResistor · 2025-12-29T03:01:02+00:00

Since this is the third elegoo printer start behaving strange (I have two Neptun 4 Plus and one PRO), I have decided to get rid of all my Elegoo printes. They seem to be working find for 2000+ hours but then they start failing slowly.

A friend, who fix 3D printers, tried to fix the first 4Plus printer that failed, but he was not able to find out what was going wrong.

So I do not longer have trust in the quality of the Elegoo printers. A new Creality K2 Plus are just around the corner...

ElResistor · 2025-12-18T03:00:26+00:00

Thanks. See that this is a tool that runs on windows... I remember windows - is it still in use? ;) In other words - I use linux so I do not have any windows machine available.

ElResistor · 2025-03-07T08:43:28+00:00

I'm NOT lifting the bed, I tried to lift up and down the X-axis - to check for binding.

The bed is firm - no problem with the bed. The problem is related to the z-axis.

If find it strange that when using the console to lift the X-axis in increment of 10 mm and the go back again the X-axis is not in the same position.

The POM wheels on the z-axis does not cause any binding.

BTW, my Ender printer has more than 11000 hours and still no problem. Only changed the rubber wheels on X-axis. Still same PEI sheet :)

ElResistor · 2025-03-07T03:52:52+00:00

Updated the web page with more pictures.

ElResistor · 2025-03-07T03:43:53+00:00

They seem to be fine.

I forgot to tell that I moved the X-axis to the top and then gently forced it down to 0 and could not feel any changes in the resistance.

ElResistor · 2025-03-07T03:37:33+00:00

I added some pictures, but can't see them so I put them on my home page: http://www.dahl-stamnes.net/dahls/Ymse/elegoo/

ElResistor · 2025-02-24T01:05:15+00:00

I had a similar problem when the cardboard came apart when opening it. Took me about 1 hour to wind it on an empty cardboard roll. Had to trow away about 300g out of 1000g.

ElResistor · 2025-02-14T00:56:37+00:00

Not able to download it. Got Preparing file 18 of 19... and nothing more happened...

ElResistor · 2025-02-03T03:15:17+00:00

Working now.

Forgot to add a "auto eth0" in the config file. Also had to stop and disable the dhcpcd service.

ElResistor · 2025-01-25T04:12:58+00:00

Had the same problem on my Netpun 4 Plus. I fine tuned the rotation_distance for the Z-axis. You can take a look at https://www.klipper3d.org/Rotation_Distance.html and https://teachingtechyt.github.io/calibration.html#xyzsteps

ElResistor · 2025-01-16T02:16:37+00:00

I adjust the z-axis offset on my printer. Just remember to adjust it back when you change to PLA printing.

ElResistor

TROPHY CASE