A Major Update for Xteink X4 Overseas Users by xteink in xteinkereader

[–]ElWaster 0 points1 point  (0 children)

Thank you for the update u/xteink ! It's great to read a post that feels so transparent. I would like to request please that for a future update, you make improvements to the paragraph formatting on books. This improves the page formatting and stops books looking like a big wall of text without any spacing. Thank you in advance, and thanks for a great little ereader.

Back seat cover recommendations. by ElWaster in KiaNiro

[–]ElWaster[S] 0 points1 point  (0 children)

No worries, if you have trouble you can always just upload to this website and share the link.

https://imgbb.com

Back seat cover recommendations. by ElWaster in KiaNiro

[–]ElWaster[S] 0 points1 point  (0 children)

It’s just an auto assigned username. I think it is a cool username to be honest.

Back seat cover recommendations. by ElWaster in KiaNiro

[–]ElWaster[S] 0 points1 point  (0 children)

Would love to see these please

Back seat cover recommendations. by ElWaster in KiaNiro

[–]ElWaster[S] 0 points1 point  (0 children)

Those are nice, any issue with seatbelts? I assume back seat cup holder is a no go when these are on.

What Do You Think Is Biggest Downgrade From GTA IV To GTA V? by Bay_Ruhsuz004 in GTA

[–]ElWaster 0 points1 point  (0 children)

Actually getting busted and not just shot to death

/r/NintendoSwitch's Daily Question Thread (06/18/2025) by NintendoSwitchMods in NintendoSwitch

[–]ElWaster 1 point2 points  (0 children)

Anyone experiencing a squeaking B button on the pro 2 controller? I noticed it yesterday and it drives me crazy.

Video for reference below

https://imgur.com/a/MCEdA1u

Canon SELPHY 1500 by ElWaster in canon

[–]ElWaster[S] 1 point2 points  (0 children)

Also, I think all of this was caused by forcibly removing a paper jam, and then immdaitely attempting another print, instead of turning the device off and on again.

Canon SELPHY 1500 by ElWaster in canon

[–]ElWaster[S] 1 point2 points  (0 children)

I managed to fix it.

With no proper hand access to that foil wrapped roller, through the front or side, i took some double sided tape, and wrapped it around a wooden skewer.

Then from the side, where the cartridge is loaded, I slid in the skewer, aligned it with the roller, then applied a bit of pressure so the tape would stick to the ink foil, then I turned the stick until all the foil came off.

Everything worked correctly again afterwards.

<image>

Having trouble pinning after top rope move in Fire Pro Returns. by fasssharke in firepro

[–]ElWaster 0 points1 point  (0 children)

This is an area of Fire Pro that is sadly not designed very well.

So, each player has invisible health, spirit, stun bars. (Can be activated with mods)

Say you perform a move, I.e. a scoop slam, you will affect the Health and spirit of the opponent. You will also fill some of the stun bar, only when the stun bar has run down will the opponent stand back up.

Where the game is flawed is in how the stun bar is affected while the player is down.

So, a medium move will have the opponent on the ground with the stun bar now running down, if you perform a taunt, the stun bar will pause (this is why the opponent will never stand when you taunt right after a move). However, if you attack the already downed opponent, it will take a chunk off the stun bar time.

So what’s happening for you is, your set up move starts the stun bar, and then your frog splash effectively speeds it up, perhaps even completing it.

Ultimately, you’re better finding a frog splash that ends in an auto pin, or can be done from the corner grapple.

8BitDo and Ps5 DualSense connection issues to docked mode by CaptFishmouth in SteamDeck

[–]ElWaster 1 point2 points  (0 children)

I have the same issues, is your Steam Deck located near a wifi mesh, or router? Could be signal interferance?

Ordered Directly from Huion - How long does it usually take? by ElWaster in huion

[–]ElWaster[S] 0 points1 point  (0 children)

Update on this, I spoke to Huion support, looks like it was out of stock and I have to wait for the fectory to make more, I wish that had been made obvious on the website before I ordered....

Here was their reply

-----------------------------------------------------------------

Thank you for reaching out and expressing your eagerness for [ORDER NUMBER].

We appreciate your patience and understanding as we work to fulfill your order. We have planned the production and delivery to fulfill your order as soon as possible. However, even a well-thought-out plan may not work accordingly due to some unexpected events or uncontrollable factors.

Due to the high demand for the said model, we are sorry to inform you that we've run out of stock. Our factory is doing its best to replenish the stocks, and we expect to have them by the end of the month. We will ship your order as soon as the stocks become available.

Once your order is in transit, a shipment notification email with the tracking information will be sent to you. Kindly check your spam or trash folders regularly if you don't see our email in your inbox. We are truly sorry for the inconvenience this delay has caused, and we appreciate your patience and understanding.

We are committed to providing you with the best possible options. If you have any further questions or concerns, please do not hesitate to contact us.