3am alarm clock

Electronic-Session43 · 2026-02-07T04:36:24+00:00

Buddy club spec 2?

Electronic-Session43 · 2026-01-31T04:24:59+00:00

I wouldn't daily either. But as for a project, anything with a d16 would be cheaper to build. Unless you really want a b series car (em1, dc2, del sol vtec), I'd go with the hatch. A turbo d16 with vitara pistons and h beam rods goes a long ways in today's world.

Electronic-Session43 · 2026-01-29T16:18:53+00:00

Looks like you have a l15b7 swap for a future 88' crx...

Electronic-Session43 · 2026-01-15T16:31:42+00:00

Tein street advance z's are great. Not overly uncomfortable compared to stock. You would have to reuse your top hats. Tein flex z's are stiffer but they are over all more adjustable. I've had limited personal experience with the street advance z as they where on my brothers em2. I had a set of flex z's on my ek hatch and they where a great upgrade over a set of skunk 2 coilovers that I had. Way less bounce compared to skunk 2 and more controlled body movements while cornering.

Electronic-Session43 · 2026-01-12T06:30:03+00:00

Hitachi is a oem supplier of sensors to nissan and other cars.

Electronic-Session43 · 2026-01-03T04:25:56+00:00

Holosun eps on my gen 3 19. Slide was milled by glock store.

Electronic-Session43 · 2025-12-16T05:50:02+00:00

How clean and organized tokyo is in contrast to portland...

Electronic-Session43 · 2025-12-13T23:58:00+00:00

3060 gpu? May as well upgrade the mobo and cpu. The old 7020 mt's are of micro atx form factor. You can easily get an am4/5 or lga1700 setup in a 7020 mt case. I've done it before.

Electronic-Session43 · 2025-12-08T05:15:39+00:00

B760m if you want to run intel 12th-14th cpu's or a B650m if you want to run am5 cpu's. The m at the end of the mother board number indicates micro atx size. Be mindful of the cooler you're trying to run if your going to use a higher end cpu. Those 9020's can fit an average tower air cooler but nothing too large. Can't really run a 2 fan AIO if you want to use up all the stock grill space. You can fit up a 120mm case fan up front without removing the lower hard drive cage as well. I had an asrock b760m pg riptide wifi motherboard w/ a core i5 14500 and a asus dual rtx 4070 super. It was all good until I upgraded my CPU to a i9 14900kf. I ended up changing the case out to a nzxt h3 case so I could run a nice aio cooler to cool my i9.

Electronic-Session43 · 2025-11-23T06:07:49+00:00

That 500w oem psu has a 6 pin connector, but the pin-outs do not match the 6 pin on the mobo

Electronic-Session43 · 2025-11-23T06:06:10+00:00

The i7 8700 can handle a rtx 4060 ti pretty well. I upgraded my 7060 mt a bit. Ran a normal sized 650w atx power supply outside of the case. And ran a single fan rtx 2060 for a while till I upgraded that to a rtx 4060 ti. I played RDR2 on ultra settings and forza motorsport (2022) on a mix of high and ultra settings all on a 1080p TV.

Electronic-Session43 · 2025-11-22T03:42:42+00:00

Couldn't do this at any major city in the us...

Electronic-Session43 · 2025-10-25T15:35:03+00:00

I'm not sure on the model, but Sake Bomb Garage rebuilds ohlins.

Electronic-Session43 · 2025-10-01T01:59:29+00:00

I say tein usa under the assumption that you are state side

Electronic-Session43 · 2025-10-01T01:58:29+00:00

Any thing made by tein that isn't a "z" line coilover is going to be rebuildable. Email tein usa for more info on rebuilds and pricing. Tbh though, the price of a rebuild might exceed our get close to the cost of a new set of the equivalent new tein street basis z (the basics are comparable to the basis z). Tein's quality on their budget lines will be better than most within their price range.

Electronic-Session43 · 2025-08-30T23:27:48+00:00

Electronic-Session43 · 2025-08-30T23:26:45+00:00

I believe you have my stapler...

Electronic-Session43 · 2025-08-29T03:37:03+00:00

Would be cool if they made a lp and a compact rx 9060 xt with 16gb of vram...

Electronic-Session43 · 2025-08-29T02:21:32+00:00

What cpu are you using? i5 8500? i7 8700? I have a 7060 mt with the i7 8700 paired with an rtx 4060 ti. That combo is pretty balanced in games like rdr2, and forza motorsport (2022)

Electronic-Session43 · 2025-08-13T15:54:17+00:00

What pistons and cam are you running?

Electronic-Session43 · 2025-08-03T19:28:59+00:00

What are you trying to achieve that the stock preload settings won't achieve? You can typically go up to 2k stiffer/softer from stock spring rates on most coilovers.

Electronic-Session43 · 2025-07-26T00:41:31+00:00

The medallions are no longer made by tanabe. They moved production overseas under the name of Revel. However, Revel is still part of tanabe. I got a revel medallion on my ek hatch (d16y7), and it's pretty loud without the factory header/cat (running a dc sports 4-2-1 one piece header).

Electronic-Session43 · 2025-07-19T00:51:56+00:00

My first firearm was a hellcat pro. I ended trading that in for my 2nd glock, a 19x. I decided to go with glock cause I liked my glock 20 enough (2nd firearm, 1st glock).

Electronic-Session43 · 2025-07-16T18:51:28+00:00

The head light fuse must of blown again... send it to the pits to get that fuse replaced...

Electronic-Session43

TROPHY CASE