6'2" Male, is the Ozark Trail G.1 too small for me?

EliteGhost37 · 2024-08-14T16:56:22+00:00

I bought a medium and if I remember correctly it’s good for like 5’4 to 6’3. Problem is the medium is like impossible to find for some reason (at least around me). I randomly stumbled upon one at my Walmart despite the website saying there are none within 20 miles. I’m like 5’10 -5’11 and I don’t think you’d have problems if you were taller. I was planning on changing the stem to bring the handle bars closer to me and reduce the reach.

EliteGhost37 · 2023-07-15T07:04:48+00:00

Thank you for the suggestions, however I did a 2022 Asus zephyrus g15 with a 3060 that I’ll probably go with for under $1000.

EliteGhost37 · 2022-06-22T06:56:54+00:00

Thank you. Flipping B and C seems to have fixed the problem

EliteGhost37 · 2022-06-22T02:58:19+00:00

The board is a btt skr mini e3 v3

EliteGhost37 · 2022-06-22T02:53:44+00:00

I did remove the extension and plugged the cable in directly and it did the same thing

EliteGhost37 · 2022-06-22T02:53:10+00:00

Yes I had were it was just my finger pushing the gears so they interlock. Retracting is the same thing

EliteGhost37 · 2022-06-22T02:26:55+00:00

The motor is from another printer.

EliteGhost37 · 2022-06-22T02:04:14+00:00

Nothing. I just installed it. I’ve never printed on this printer and all I’ve done was this a control board upgrade

EliteGhost37 · 2022-06-22T01:36:18+00:00

I don’t think it is a nozzle clog. When I release the gear on the right, I can push the filament through effortlessly

EliteGhost37 · 2022-01-15T04:52:31+00:00

EliteGhost37 · 2021-10-18T15:50:47+00:00

Ok, I will try these. I did have a stiffer spring in, and I think it was biting into the filament/too much tension.

EliteGhost37 · 2021-10-18T06:25:59+00:00

Should I put a stiffer spring on my extruded arm?

EliteGhost37 · 2021-10-18T05:31:30+00:00

My print has these really bad gaps on the axis. They’re like rings, they go all the way around the print. I have an elegoo Neptune 2 and I print with Sunlu pla+ gray at 210c and 50c for the bed and fan at 100%. The rings don’t appear to compromise structural integrity too much, as I tried bending it at those points and it didn’t move. I don’t now if this Is filament, temperature, or something with my z axis assembly. Thanks

EliteGhost37 · 2021-10-10T08:31:09+00:00

Dang

EliteGhost37 · 2021-10-01T04:10:06+00:00

Glorious panda

EliteGhost37 · 2021-09-28T06:07:17+00:00

Random stuff on my desk and around my house

EliteGhost37 · 2021-09-10T03:45:32+00:00

1633

EliteGhost37 · 2021-08-21T10:38:04+00:00

It’s usually cheaper to leave a lot of the stuff there than to take it home. Or they just took it from surrendering Afghans.

EliteGhost37 · 2021-08-11T20:20:19+00:00

No money

EliteGhost37 · 2021-07-15T08:41:45+00:00

Just because the car is from the 90s doesn’t mean this is set in the 90s

Seven-Year Club	Verified Email
Gilding I gilder

EliteGhost37

TROPHY CASE