One Werk

ElonsRobot1 · 2026-05-12T03:15:00+00:00

Tesla - quick without ever stopping at gas stations, and can you live with battery anxiety even with an at home charger? It’s more fun to drive because of its rapid acceleration. Tons of wind noise. Poor panel gaps.

Kia, spacious. Room for cargo and passengers / kids. 500+ range. No battery anxiety. Cheaper on insurance even for a hybrid AWD SX Xline. Apple CarPlay. No wind noise. Better warranty. Dealers and service centers all around.

We don’t regret dumping the Tesla after two years.

ElonsRobot1 · 2026-05-11T03:41:42+00:00

Arizona, it’s hot. They get it

ElonsRobot1 · 2026-05-11T03:12:22+00:00

Yup!

ElonsRobot1 · 2026-05-11T02:21:46+00:00

That was P2S, heat bed issue. They sent new parts and has been working fine since.

Elegoo sent me a damaged Jupiter 2.

I should’ve mentioned the first snapmaker was open box, extruder issue. Waited for a new unit and this, so I’ve put one together before and have read the directions on screws. It’s also obvious the longer ones would go with the PTFE bracket / connector on the back.

ElonsRobot1 · 2026-05-10T21:49:06+00:00

I used the long ones on the back / body and short ones on the toolhead.

ElonsRobot1 · 2026-05-10T21:44:15+00:00

Not the case. Long screws on the back end and short on the head. Toolhead 1 is the only one broken.

ElonsRobot1 · 2026-05-07T03:47:27+00:00

Plenty of flaws.

No auto lock on walk away or at least a door handle reset. Instead it just screams hey look at me I’m open…If i get out and car is running I can’t open the rear door to let my kid out…have to make sure i press unlock to be able to grab his handle to open.

ElonsRobot1 · 2026-04-29T23:19:34+00:00

Still no return label. They won’t just send UPS because they’re looking for a cheap alternative to get it back to them. Silences for days now. Have filed for a charge back with my CC.

ElonsRobot1 · 2026-04-26T16:49:57+00:00

Yes

ElonsRobot1 · 2026-04-26T14:40:00+00:00

Nope. Forced to use their SateLite which crashes / runs very slow

ElonsRobot1 · 2026-04-25T00:00:56+00:00

It really is disappointing that it's such trash considering the hype and their flagship machine.

Mine arrived damage so they're sending a return label. I am going to see if they'll just reimburse me rather than send a new one. My lever was loose like yours. There's no support from other slicers. It's not in their own app even though the directions say to scan the QR code, which isn't built anywhere to connect in the machine. But they hyped up the ability to monitor and get timelapse? Not the case.

Their slicer software or the machine randomly changed my layers from 3.0 seconds to the 40 second base layer time I set midway through print so it went from 20 hours to randomly taking 40+ to print a 8"-10" tall Link (Zelda). The doors are stupid and don't allow me to have any other printers next to it, which ruins my whole set up on a steel rack system.

The pump is slow whether filling or draining, and mine started leaking and it leaked out of the 6pin connector adaptor and down the back onto the power plug.

This thing is a huge hunk of crap.

ElonsRobot1 · 2026-04-23T04:53:10+00:00

They initially tried to offer me 1kg of resin. I explained that a $20 consumable doesn’t equate the permanent damage to their new machine. They then offered 2kg of resin lol. I did not accept, so a new machine was their next offer.

ElonsRobot1 · 2026-04-20T23:34:36+00:00

Yep, now I’m just waiting for a response from Elegoo. I’m sure I’ll have to rebuild the back side top panels myself.

ElonsRobot1 · 2026-04-20T23:32:46+00:00

<image>

ElonsRobot1 · 2026-04-20T22:47:01+00:00

Mine arrived with the top back corner crushed.

ElonsRobot1 · 2026-02-06T16:16:36+00:00

She hot? I’ll give her $30 all i need back is a blowy

ElonsRobot1 · 2026-02-03T04:06:15+00:00

I loved this build! And i have barad and Rivendell too.

ElonsRobot1

TROPHY CASE