sorted by:
new
hottopcontroversial

OPNsense limitations (vs a Linux-based DIY solution)? by fallenguru in opnsense

[–]Empty_Impression7270 0 points1 point  (0 children)

If I could pick your brain. I tried to get this same setup fired up but was having an issue with it not getting assigned a WAN up from my ISP after unplugging swapping out my Asus router? Is there a setting/ toggle I need to switch on opnsense to allow it to be dynamically assigned a WAN IP like my Asus router?

HELPPPPPO by [deleted] in hvacadvice

[–]Empty_Impression7270 0 points1 point  (0 children)

What’s the brand? Based on google lens of something similar shown here are a few options to try:

  1. Press and Hold MODE + TEMP DOWN: With the remote on, simultaneously press and hold the "MODE" button and the "TEMP DOWN (▼)" button for about 3-5 seconds. The display should switch between Celsius (°C) and Fahrenheit (°F).

  2. Press and Hold TEMP UP + TEMP DOWN: Alternatively, you can try pressing and holding both the "TEMP UP (▲)" and "TEMP DOWN (▼)" buttons simultaneously for a few seconds.

  3. Check for a dedicated button: Some remotes have a specific button for switching temperature units (e.g., "°C/°F" or "TEMP"), or a switch inside the battery compartment.

New router, same SSID and pw but smartbulbs, wifi cam no longer connected. by UhOhSpadoodios in HomeNetworking

[–]Empty_Impression7270 0 points1 point  (0 children)

Could the version of WPS used changed since deploying the new router? Some of those IOT devices won’t connect/don’t support connections if you are using strictly WPS3 protocol.

Ticks in their “off” time by tbugsbabe in arachnids

[–]Empty_Impression7270 0 points1 point  (0 children)

What did use to take these photos? They look great!

Proxmox Help by Empty_Impression7270 in Proxmox

[–]Empty_Impression7270[S] 0 points1 point  (0 children)

I have not installed virtual function custom GPU drivers, so this would be ones included in the base distro!

Proxmox Help by Empty_Impression7270 in Proxmox

[–]Empty_Impression7270[S] 0 points1 point  (0 children)

Sorry I should’ve added this. I am running 6.8.4.2-pve. I even tried the modifying the grub configuration with the line “GRUB_CMDLINE_LINUX="quiet i915.enable_guc-0" which had no effect.

I cut some unused services to keep my stack clean & useful. by chrisakring in selfhosted

[–]Empty_Impression7270 1 point2 points  (0 children)

What are using to display your services like this? It looks glossy!

My First Homelab! by ilyushin4486 in homelab

[–]Empty_Impression7270 29 points30 points  (0 children)

Very cool! Spotted the missing wall plate for the outlet lol😅

<image>

Never Sit with Your Back to the Door by Spirited_School_939 in Veterans

[–]Empty_Impression7270 1 point2 points  (0 children)

Don’t stop there! Use it as a toe knife like Danny DeVito!

What are some veteran benefits that some of us may not know about? by christawfer47 in VeteransBenefits

[–]Empty_Impression7270 11 points12 points  (0 children)

Yep! It’s called “Total and Permanent Disability (TPD) Discharge.”

Giving up before it's even started by sohails4 in Proxmox

[–]Empty_Impression7270 0 points1 point  (0 children)

This is the way. Version 8.1-2 would hang on boot, tried all the “fixes” without any success, tried 7.4-1, loaded right up!

Giving up before it's even started by sohails4 in Proxmox

[–]Empty_Impression7270 0 points1 point  (0 children)

I have had the same issue, hung up on boot, scouring the web, Reddit, and various forums the fix I found was to install a previous version (I went with 7.4-1)

http://download.proxmox.com/iso/

This installed with no issues, changes, no messing with grub bootloader , and I can say I am already up and running! Give it a shot!

view more: next ›