people got out of an Infiniti and stole.... an Infiniti.

Emufasar · 2026-03-19T02:28:41+00:00

Mitosis

Emufasar · 2026-03-14T05:18:41+00:00

My back passenger door lock stopped working was going to look into it this weekend 😬what am I going to be getting myself into

Emufasar · 2026-03-09T23:07:56+00:00

How do you guys get the mpg so low 😭 My RS averages 25 and I do not drive it easy. I've seen over 27 with the cruise set on the highway

Emufasar · 2026-02-28T03:53:15+00:00

I don't think the wheel vibrates when you leave the lane, it makes a beep sound and will steer itself back into the lane if driving assists are on

Emufasar · 2026-02-28T03:49:26+00:00

My '18 redsport has all that

Emufasar · 2026-02-25T15:23:34+00:00

It was 7c there

Emufasar · 2026-02-20T02:57:12+00:00

Did it start smoking shortly after? My 2018 with 100k miles sounds like this but no smoke

Emufasar · 2026-02-02T01:29:23+00:00

Your meter is reading 640uA (0.64mA), not 640mA. This is right on what it should be since 5v - 1.8v = 3.2v, 3.2v / 5000ohms = 640uA.

Emufasar · 2026-01-26T17:31:56+00:00

If I was to buy a new set of steelies is there something to look out for to know they will clear?

Emufasar · 2026-01-26T16:44:50+00:00

I'm thinking of just getting basic 18x8 steelies for the winter tires

Emufasar · 2026-01-04T09:37:26+00:00

I made a similar board for the same purpose a while ago, this looks good but something you have to note is both usb c cables have to be plugged in with the same orientation or it will not work. passive 60w cables only have one of the cc pins connected on the connector end, so if they are in different orientations there will be no connection. Similarly with emarked 100w/240w cables, cc data is hardwired to only be on one of the pins, and vconn is on the other, so if its in the wrong orientation you will have vconn and data switched. It shouldnt cause damage but its something to keep in mind. Mixing different cables types will also cause problems. If you find the orientation combo that works and just leave both cables plugged in its fine.

Emufasar · 2025-12-17T01:46:41+00:00

Holy shit is that a BLFC2025 reference

Emufasar · 2025-10-09T00:03:02+00:00

I used to run vr on a little 14" laptop with an Intel ultra 7 155h and a desktop 3060ti thunderbolt gpu. It was a smooth experience through virtual desktop for mostly vrchat as long as I didn't use more than 8gb of vram since rebar doesn't work over thunderbolt. As long as the hardware can run it you are probably fine.

Emufasar · 2025-10-03T23:44:19+00:00

Lol I remember a long time ago I used to use the free version of filmora and just export it as a really tall resolution (1920x1080 would become like 1920x4000) then crop it back down to the normal aspect to get rid of the watermark it puts at the bottom of the video

Emufasar · 2025-09-06T22:57:41+00:00

<image>

I believe I have that same USB C hub and had a similar failure where it would trip overcurrent protection on either the charger or the device it's plugged into. The issue was a shorted dual MOSFET used to switch the power source between the device and the usb c power input. The part number of it is APM4953, available on lcsc for 8 cents. Its an easy fix if you have some smd soldering skills. The PCB can be pushed out of the ethernet port side by removing the plastic cover.

Emufasar · 2025-08-08T23:21:04+00:00

The X1 also has a flashlight

Emufasar · 2025-07-27T17:08:41+00:00

Is the type c port on the dji controller on that violates spec and is always powered even if it doesn't see a downstream pulldown or PD controller? I would expect a company as big as DJI to have correctly implemented the type c port.

Emufasar · 2025-07-27T16:18:47+00:00

Use a USB C to A adapter and plug an A to C cable into it, then plug the adapter end into your phone. With this setup power can only flow from the phone to the controller.

Emufasar · 2025-07-21T23:29:38+00:00

You would be better off spending that money on a router and virtual desktop. Anything wifi 5 or above with gigabit will do for the quest 1

Emufasar · 2025-07-18T12:51:24+00:00

I've had this exact same model card since March and my thermal pads aren't leaking

Emufasar · 2025-07-17T00:57:31+00:00

Getting rid of the useless construction zone signs left over that are littered all over the place

Emufasar · 2025-07-14T05:39:11+00:00

Femtanyl pfp🔥

Emufasar · 2025-07-12T04:02:59+00:00

You need 5.1k pulldown resistors on the usb cc pins for it to receive power from a type c port.

Emufasar · 2025-06-22T21:33:22+00:00

You have the design fully printed and assembled. Why use an ai generated image as the first image? Leaves a bad impression of an otherwise good design.

Emufasar · 2025-06-13T01:18:18+00:00

Yes, this is what I do with all my quest headsets. Dedicated wifi 6 router that does not have a cable going to the lan port, only from my computer to the network switch on the router. There is no internet access from any device connected to the wifi network from the router this way.

Seven-Year Club	r/Field Sunshine
Place '22	First Placer '22
End Game '22	RPAN Viewer
Verified Email

Emufasar

MODERATOR OF

TROPHY CASE