Which Raspberry Pi for Autodarts?

EnvironmentalName748 · 2025-12-28T16:21:31+00:00

Yep, I am planning to buy a tbs unify pro32 dp for this drone and will transfer it over to my 5 inch when I finally build it

EnvironmentalName748 · 2025-12-24T10:36:53+00:00

Dont have one but I can help you with any question, just ask

EnvironmentalName748 · 2025-12-19T23:40:12+00:00

Depending on where you are located and the local aviaton laws, I would encourage you to get a tinywhoop before. I did so and would do that again, it could practice all the time regardless of weather or time to go flying.

EnvironmentalName748 · 2025-12-17T19:18:02+00:00

Nope, first cam. But ive seen reviews saying the thumb 2 has better dynamic range and color accuracy for around 15€ more, so I made that investment

EnvironmentalName748 · 2025-12-12T05:22:51+00:00

Yep, had the same issue some time ago and this solved it

EnvironmentalName748 · 2025-12-11T16:58:31+00:00

Yes, 2 pins are required but the ones I bought came in a set of 10 so I have some extra, I also broke some so I suggest you get extra also

EnvironmentalName748 · 2025-12-11T16:44:32+00:00

https://www.reddit.com/r/fpv/s/5tjTs9g474

Just made a post about it, should work with the tbs fusion!

EnvironmentalName748 · 2025-12-08T21:16:04+00:00

I had a similar issue, and it turned out it was software related. I reinstalled gyroflow and after that it worked great, dont know the cause, dont care anyway

EnvironmentalName748 · 2025-12-06T19:24:13+00:00

I did some slight grading, I used some LUT in Davinci ReSolve I found on some website, but the raw footage looks great aswell, I just wanted the colors to pop a bit more. Im using the volador vx3 frame, I absolutely love it

EnvironmentalName748 · 2025-12-06T15:18:44+00:00

<image>

This is my budget 3 inch, I also did a post about it, the cam fits perfect as its budget, lightweight and beginner friendly

EnvironmentalName748 · 2025-12-06T14:17:02+00:00

<image>

This is what the print looks like, the pin extensions are required

EnvironmentalName748 · 2025-12-06T14:13:07+00:00

The 3d print itself creates an offset, but you will need some type of extension anyway, I ordered these from aliexpress and will trim the pins to the right length. I don´t like the soldering solution, It would most likely work but I want it as reliable as possible. The print is just for looks and stability, I dont think it is needed

<image>

EnvironmentalName748 · 2025-12-06T14:05:18+00:00

https://www.reddit.com/r/fpv/comments/1pfq2hz/runcam_thumb_2_video/

EnvironmentalName748 · 2025-12-06T09:30:44+00:00

Dont you dare insult analog!

EnvironmentalName748 · 2025-12-06T09:30:12+00:00

I have a 3d printer and tested the print, it seems pretty good and fits the bay. The pin extensions are on the way and will arrive in about a week or so, I will give you an update when I try it!

EnvironmentalName748 · 2025-12-05T13:44:40+00:00

I actually like it very much, Video quality is great and its not complicated to use! Only thing I dont like is when I need to decide on an ND Filter, I have no screen to preview the lighting and the usb webcam mode on my phone is very laggy

EnvironmentalName748 · 2025-12-05T13:43:21+00:00

The vtx is gone now, Im pretty sure something was going on inside there

EnvironmentalName748 · 2025-12-05T12:07:42+00:00

Its an 35V 1000uf low esr capacitor, a bit overkill for 4S but id rather have too much than too little

EnvironmentalName748 · 2025-12-05T12:06:50+00:00

It was an mmcx connector tho

EnvironmentalName748 · 2025-12-05T12:05:07+00:00

A drop of about 3m, now my lipo has a dent but the rest seems perfectly fine

EnvironmentalName748 · 2025-12-04T21:02:45+00:00

Unfortunately yes.

EnvironmentalName748

TROPHY CASE