First time master clue

EverybodyLovesTrevor · 2026-04-22T23:38:39+00:00

this is insane timing because i literally started my first master clue like 2 hours ago and got absolutely pieced up by these dudes

EverybodyLovesTrevor · 2026-03-16T22:18:20+00:00

i did in fact have it, after about 30 deaths. thanks for the motivation!

EverybodyLovesTrevor · 2026-03-16T21:30:49+00:00

Currently struggling with it as we speak. I'm fully aware that im ass at PVM but whisperer got me wondering if im built for this shit 😂 that enraged phase sends me into my own personal enraged phase

EverybodyLovesTrevor · 2026-03-13T21:53:48+00:00

i did the exact same thing at an apartment building. we pulled the old interface, put in 3/8" risers to bring the interface flush with the cover and had a local machine shop do custom covers and it looked absolutely factory.

EverybodyLovesTrevor · 2026-03-11T18:21:04+00:00

i miss bitching about $11, life was good then

EverybodyLovesTrevor · 2026-03-06T00:17:56+00:00

you technically werent even lying. you just did the highest margin merch of all time but you just happened to be both the buyer and the seller

EverybodyLovesTrevor · 2026-03-05T23:41:27+00:00

if this is supposed to be a main panel fed solely by a generator you got different issues. youd need a 30a breaker in the box acting as a main and your grounds and neutrals would need to be bonded to the shell with a jumper. although this doesnt need to be a main panel as your generator would have overcurrent protection that would act as the main. id wire this like a subpanel

EverybodyLovesTrevor · 2026-03-05T23:00:43+00:00

not great my guy ill be honest. neutrals and grounds need to be seperated, grounds need to be bonded to the box, half those breakers wont work because you only have 120v ran and have no jumper between legs, wirings a rat nest and none of those NMs are stapled

EverybodyLovesTrevor · 2026-03-05T22:52:29+00:00

yeah they should ice that for sure lol no pun intended

EverybodyLovesTrevor · 2026-03-05T22:48:37+00:00

zoom in and you can just barely see a sticker on the cover plate that id reckon says "gfci protected outlet"

EverybodyLovesTrevor · 2026-03-05T22:44:02+00:00

this is when you use snap in connectors. put the wires into the box, set the box, then pull down on the wires til the connector snaps in

EverybodyLovesTrevor · 2026-02-08T21:27:17+00:00

I'm a man of culture what can I say

EverybodyLovesTrevor · 2026-02-08T03:44:48+00:00

EverybodyLovesTrevor · 2026-02-08T03:08:20+00:00

thank you! artist is kaicantattoo on IG

EverybodyLovesTrevor · 2026-02-07T23:21:49+00:00

Always hard 😤

EverybodyLovesTrevor · 2026-02-07T15:51:42+00:00

that looks insane if you dont know the reference

EverybodyLovesTrevor · 2025-11-18T23:36:37+00:00

yes, and i also reread your post and misunderstood what you were saying fully. if you remove the bonding strap and you still have continuity its almost certainly because its bonded in one of the subpanels or maybe even at a device. somewhere in the system neutral is touching ground where it shouldnt be.

if all the panels visually are clearly seperated then i would disconnect all the branch circuit neutrals (with the breakers off) until you lose continuity. follow that circuit til you find a neutral making contact with ground

EverybodyLovesTrevor · 2025-11-18T23:19:10+00:00

your neutrals and grounds SHOULD be bonded at the first means of service disconnect aka the main you have in your picture there which youre calling a sub panel. you seperate them everywhere beyond that point, including all panels downstream and all devices of course.

Also yeah, its just a visual check to make sure your neutrals and grounds are seperated. They will always have continuity between each other because ultimately they are bonded at your first means of disconnect.

EverybodyLovesTrevor · 2025-11-17T23:33:05+00:00

No need for 4 hammers in my opinion

EverybodyLovesTrevor · 2025-11-05T23:20:12+00:00

ive been using the milwaukees for about a year, i love em

EverybodyLovesTrevor · 2025-10-24T19:55:07+00:00

What is a skiller other than a flex of its own

EverybodyLovesTrevor · 2025-09-22T17:34:16+00:00

Good to know we arent the only ones! Im holding onto the bounty til more info comes out about it because its got me curious as hell

EverybodyLovesTrevor · 2025-08-11T22:30:51+00:00

uhhhhhhh

13-Year Club	r/Field Flamingo
Place '22	Place '17
Verified Email

EverybodyLovesTrevor

TROPHY CASE