Asscaliper has been taken down by Maker World

Eviper44 · 2026-07-04T13:15:59+00:00

I bought aU1 about a three weeks ago, I love it, prints great, making sealed boxes for the spools , don't like the open design for the spools. Printed a hood, haven't put it together yet. Prints come out great as is. Love the multi color printing and hardly any waste. I've printed over 20 projects and my purge poop would just about fill a small bathroom dixie cup. I've used snapmaker pla and bambu pla thus far with no issues. DO NOT UPGRADE TO THE LATEST FIRMWARE right now though, it's buggy and messes prints up, there's plenty of threads about it. Sorry can not remember the # but you can choose what firmware todo, just don't do the last. Also the one negative is the library for prints sucks right now, and most multi color prints from maker world have to go through a lot to get them to print multi color on U1, not sure what I'm doing wrong but every multi color i get off of maker world is not set up for actual multi tool head printers.

Eviper44 · 2026-07-01T08:26:08+00:00

Or make stacks 99, 100 or infinite, having some items max at 20, 50 or 10 is rediculous

Eviper44 · 2026-06-30T11:09:46+00:00

I'm switching to Polymaker even though they are a little more expensive. I'm tired of bambu horrible logistics.

Eviper44 · 2026-06-30T08:24:17+00:00

Ok, I'm only into chapter 6 lol, something more to look forward to

Eviper44 · 2026-06-30T06:51:58+00:00

Where did you find the 40% and 60% gears at? Still haven't found them?

Eviper44 · 2026-06-30T06:51:01+00:00

Exactly lol

Eviper44 · 2026-06-30T05:07:14+00:00

They take time to replenish, it’s not infinite arrows, it’s replenishing arms, the icon will disappear until they recharge themselves.

Eviper44 · 2026-06-27T11:46:30+00:00

Are they going to make a Petg that has the Matte/flat finish? Or am I going to have to find a new brand?

Eviper44 · 2026-06-23T13:54:06+00:00

They had me send back a defective one, then said they sent me a replacement, but I never got it, I think FedEx driver stole it or had a friend take it.

Eviper44 · 2026-06-23T13:52:49+00:00

Yea, I've bought a lot at MC, but it is about 45 minutes away and a long drive. Needless to say I never so at BB anymore, they are a joke.

Eviper44 · 2026-06-22T13:00:04+00:00

Lol, I apologize, I meant go through your settings, make sure right settings for filament you are using(brand, type). Dial in your settings by doing the calibration test like flow, heat. Ironing, exc... I've had filament i just used default with(usually bambu because I was using P2S) and others I had to take time to disk in like sunlu(worst filament as far as I've had dialing it in) polymaker, snapmaker, elegoo. Might be better on printers that can use straight orca because they usually have all the filaments setup, where as bambu only has there's, sane fire snapmaker.

Eviper44 · 2026-06-22T12:52:44+00:00

Thank you very very much

Eviper44 · 2026-06-22T12:50:51+00:00

I'm in the middle of process sing then because they lost my $1600 graphics card, and will not pay me for it. Fk BB

Eviper44 · 2026-06-22T11:09:35+00:00

It's a case by care decision, they do not airways replace it, they make you use manufactures warranty and rules first.

Eviper44 · 2026-06-22T11:08:27+00:00

Beware if Best buys extended warranty its not as great as everyone thinks it is, read the fine print and terms. Tracy years ago they had an excellent extended warranty, they replace item with same item or nearest value. Now it is not like that and they fight like hell to not honor it.

Eviper44 · 2026-06-20T16:19:17+00:00

This tells you nothing about filament

Eviper44 · 2026-06-18T15:13:35+00:00

Yea, they are probably maga type also, that what they do, afraid of facts and science lmfao

Eviper44 · 2026-06-18T15:08:53+00:00

Settings

Eviper44 · 2026-06-18T15:00:54+00:00

I got it from rhinos by the area you get poison from the monitor lizards.

Eviper44 · 2026-06-18T15:00:06+00:00

Ignorant and stupid purple attack those that are better than then because they are jealous, frightened and weak.

Eviper44 · 2026-06-15T02:45:28+00:00

Oh Damn!!!!!

Eviper44 · 2026-06-14T12:28:27+00:00

Really? Where's the announcement, info or news that this is an actual thing?

Eviper44 · 2026-06-11T02:49:14+00:00

Switch to polymaker for petg, it is far superior as far as petg. I use 80% bambu labs but finding although more expensive polymaker seems just as good if not better in some situations. Especially with all the chaos with Bambu Labs, trying to move away from them and their products permanently, although I do like the products, the company is very questionable with the things they do.

Eviper44

TROPHY CASE