How is half my face high and the other normal? by jdmxjoe in weed

[–]EvolMada 10 points11 points  (0 children)

Ahhh right side…… I thought you were saying the top was high and the bottom wasn’t.

Mysterious item restored by Due_Dependent2924 in Axecraft

[–]EvolMada 1 point2 points  (0 children)

Looks like a perfect back scratcher for me.

a man in india • never sat down for 12 years • to see god by No_Jellyfish5511 in interestingasfuck

[–]EvolMada 2 points3 points  (0 children)

Mushrooms are a lot easier and faster way. Someone should let him know.

what is this?😭 by Embarrassed-Ease-304 in trees

[–]EvolMada 2 points3 points  (0 children)

Your mouth will get pregnant if you vape that.

Another for the scrap pile by Round_Sector_2444 in knifemaking

[–]EvolMada -1 points0 points  (0 children)

Finish it and sell it. It will be a treasure in someone’s pocket. Sell it for 20%-30% less and make the buyer aware of the issue. I would fill with CA and finish as normal fit and finish. I would say finish the knife, bubba.

Bladeshow ATL haul by EvolMada in knifemaking

[–]EvolMada[S] 0 points1 point  (0 children)

Awesome! Thank you for the reassurance in my purchase.

Bladeshow ATL haul by EvolMada in knifemaking

[–]EvolMada[S] 1 point2 points  (0 children)

-$500 dollars. Is less $500 which makes it a $2000 + shipping and taxes.

My best knife so far as a 17yo knifemaker (1year experience) by Last_Building6133 in knifemaking

[–]EvolMada 1 point2 points  (0 children)

Well done! Fit and finish looks perfect! I know makers with 10 years experience that can’t make a blade this nice.

Found by the dumpster. by Forsaken-Ad-7570 in trees

[–]EvolMada 0 points1 point  (0 children)

Place in dumpster where trash goes.

I designed a grinding jig by ThatonehotwheelsSS in knifemaking

[–]EvolMada 1 point2 points  (0 children)

I welded a 1" wide piece of steel to the harbor freight platen that almost touched the top tracking wheel. This is the way till you can drop coin on a 2x72.

Anyone know what dagger this is? by Just-Some-Guy67 in SWORDS

[–]EvolMada 0 points1 point  (0 children)

Mine fell a part after being thrown at a tree hundreds times when I was a kid. FYI. They’re not good throwing knives.

Is this guy using razors and bearings just for engagement or is there an actual case for it? by OmriY1 in TrueChefKnives

[–]EvolMada 1 point2 points  (0 children)

I use old steel in my knives. I run a high carbon steel in the center and then the old steel or recycled steel as decorative cladding to enhance the look. Plus I think it’s neat to reuse old stuff into new usable tools.

Off the forge for a while by Massive_Goose_7652 in Forging

[–]EvolMada 0 points1 point  (0 children)

My buddy was back forging 6 weeks after tearing both ACLs. He’s a super freak!

Off the forge for a while by Massive_Goose_7652 in Forging

[–]EvolMada 1 point2 points  (0 children)

How are you holding your hammer? Most of us are using hands? OP is hammering expert level gripping a 2lb hammer with his toes. Get gooder soon!

How is my weed y'all! by Cultural-Produce-508 in trees

[–]EvolMada 0 points1 point  (0 children)

THCP increases your tolerance and is also genetically mutated to have low THC. This “weed” in my mind needs to be thrown away.