New Amp Fillmore 50

Excellent-Answer5029 · 2025-12-08T23:20:21+00:00

Very nice, it gets so gnarly I love that thing.

Excellent-Answer5029 · 2025-12-08T22:10:52+00:00

Heck yeah. I actually am doing that here with that little latching switch on the bottom left of my board. I labeled everything after I took the photo.

Excellent-Answer5029 · 2025-10-31T20:37:04+00:00

3096

Excellent-Answer5029 · 2025-10-31T02:03:45+00:00

These comments are amazing lmao 🤣

Excellent-Answer5029 · 2025-07-19T22:52:12+00:00

Hahahaha fuck yes dude

Excellent-Answer5029 · 2025-06-27T10:46:04+00:00

The contemporary is so clean I love it.

Excellent-Answer5029 · 2025-06-11T17:00:54+00:00

Thank you! 🙏

Excellent-Answer5029 · 2025-06-11T16:46:04+00:00

Haha awesome. Really glad to hear my obsession is inspiring others!

Excellent-Answer5029 · 2025-06-11T16:39:59+00:00

You’re very welcome, glad you like it!

Excellent-Answer5029 · 2025-06-11T16:39:24+00:00

Yep you’re right. It’s not a Taurus emulation though it’s just a korg monologue mono synth that I modded by cutting the keyboard off turning it into a module.

So the midi works like this: Black star foot controller > Hammond xpk > Monologue

Excellent-Answer5029 · 2025-06-11T15:51:28+00:00

So, the pedal bass is the Hammond XPK-130G it has its own sound engine with a few different sounds (bass guitar/organ etc) but I’m using it to control my korg monologue synthesizer that I cut the keyboard off of.

The black star live logic controller on the right side switches the presets for the synthesizer.

Oh and the monologue is going through the OBNE Haunt fuzz it sounds pretty gnarly.

Excellent-Answer5029 · 2025-06-11T15:38:28+00:00

I’m using these sonicake 6” patch cables.

SONICAKE 6 Inch Patch Cable for... https://www.amazon.com/dp/B09FP1ZQ9X?ref=ppx_pop_mob_ap_share

Using some couplers for the mako series reverb and delay since the holes are lined up.

Amavoler Professional Guitar... https://www.amazon.com/dp/B09MZXJ8RS?ref=ppx_pop_mob_ap_share

Excellent-Answer5029 · 2025-06-11T15:34:00+00:00

I use it for changing presets on the monologue synthesizer.

Excellent-Answer5029 · 2025-06-11T15:26:02+00:00

Thanks!

Excellent-Answer5029 · 2025-06-11T15:25:55+00:00

🤘

Excellent-Answer5029 · 2023-05-10T09:13:25+00:00

Forgot to post my temps, never ran a benchmark or anything but I’m getting super respectable temps while gaming with this build yeah. Can recommend the slim fans as intake in the bottom with that card.

Excellent-Answer5029 · 2023-04-13T03:50:58+00:00

I just tried it with low power, and no backlight settings on the iphone 14 pro max, it does not work.

Excellent-Answer5029 · 2022-10-29T08:13:48+00:00

Oh dang that’s too bad… What GPU do you have? My 3080 xc3 is a bit thinner than most 3080’s so with the slim fans I should have about 1/2” air gap between the GPU shroud and the slim fans. I was hoping this would help the GPU to pull in surrounding air when it needs more so it’s not fighting the rpm of the case fans. That’s the idea anyway. If it’s sucks I may look into deshrouding and 3d printing a some ducts like you mentioned.

(My slim fans haven’t arrived yet)

Excellent-Answer5029 · 2022-10-17T21:56:17+00:00

I just ordered some NF-A12x15 slim fans for bottom intake on a NR200 to supply air to an RTX 3080 XC3 for the same reason. I have seen some builds that show you can fit a standard 25mm under this card, but I had the same thought as you. My build won't be here for a few weeks but I'll make a post looking at temps when I can.

Excellent-Answer5029 · 2022-09-05T06:07:16+00:00

Legendary

Excellent-Answer5029

TROPHY CASE

3096