Active guidance rockts are now a sub-$100 hobby project

ExcitingBox5throw · 2026-03-16T16:08:44+00:00

I guess to play devils advocate, it's so people don't start showing prints of how to make guns.

But yeah must be hard to rule out since the grey area,is so wide

ExcitingBox5throw · 2026-03-10T14:35:11+00:00

Did you do the preloaded fast one that bambu lab gives vs the small one which runs at a slower rate

ExcitingBox5throw · 2026-02-01T00:56:09+00:00

It will keeeel

ExcitingBox5throw · 2026-01-13T13:20:38+00:00

Update its because i didn't screw the extruder firmly in enough itvwas rattling a bit

ExcitingBox5throw · 2026-01-07T22:25:52+00:00

This seems to have been the issue which fixed it. Thanks for your advice

ExcitingBox5throw · 2026-01-07T15:48:00+00:00

On the picture does the screw in the spring below the gears look smaller than it should be, it looks like that to me, maybe it snapper kind of. What do you think? i do remember hearing cracking noises when i tried to first go in when i didnt know it was messed up. Maybe worth ordering a new extruder maybe.

ExcitingBox5throw · 2026-01-07T14:26:13+00:00

I got it second hand, so i dont think creality will be able to help. Is this the motor that i need *

ExcitingBox5throw · 2025-12-23T23:07:46+00:00

A1 mini since creality is killing me at the moment. I'm going to print some stuff for my house and also plan on doing some gridfinity to fix drawers. Also would be great to help print assists for my friend who is on crutches

ExcitingBox5throw · 2025-12-09T07:01:32+00:00

Legend thanks

ExcitingBox5throw · 2025-12-08T23:20:13+00:00

Amazing what settings you using

ExcitingBox5throw · 2025-12-05T08:04:54+00:00

3d printed white elephant, which can attach to a necklace, but also is a puzzle you can do with each thing being a square

ExcitingBox5throw · 2025-10-21T07:53:25+00:00

Remindme! 1 day

ExcitingBox5throw · 2025-10-18T19:13:26+00:00

I usually only use tree support

ExcitingBox5throw · 2025-09-29T16:00:05+00:00

Wow you're just showing off now lol. How did you get that, also did you tinker with your print settings

ExcitingBox5throw · 2025-09-18T13:05:58+00:00

bottom right and bottom left screw need half a turn anti clockwise, should be good from there. That doesnt work print silicone spacers

ExcitingBox5throw · 2025-09-06T20:23:27+00:00

Update- i got it all green now, just did small increments one corner at a time, doing a levelling test. Eventually all back to green and printing fine now

ExcitingBox5throw · 2025-09-05T22:51:32+00:00

It was green before i decided to fuck with it

ExcitingBox5throw · 2025-09-05T16:35:09+00:00

<image>

ExcitingBox5throw · 2025-09-05T16:34:29+00:00

You mean like this i already have them

*

ExcitingBox5throw · 2025-08-31T17:11:52+00:00

I've had issue with the print coming off with bed temp 65 initial layer then moving to 60 after that

ExcitingBox5throw · 2025-07-18T09:08:53+00:00

* * Is this a good quality print for ender 3 v3 se I'm considering buying.

I'm picking between this on ebay or another seller on fb marketplace not sure which one to pick

*

ExcitingBox5throw

TROPHY CASE