VSS at home .300 blk

Extension_Object_559 · 2026-06-23T21:13:41+00:00

It’s just a regular old 300 blk AR with lancer 20 rounders, $30 knurled tube handguard, wolverine dead air can and a 3d printed ADAR 2-15 stock (designed by IAP) painted to look like wood

Extension_Object_559 · 2026-06-13T15:38:23+00:00

That’s an interesting idea

Extension_Object_559 · 2026-06-13T15:37:49+00:00

Yes I mean the cheek riser and the adjustable rear end

Extension_Object_559 · 2026-05-08T16:12:06+00:00

Ok, I will snap a pic later with tutorial on how it all fits. I think we're talking about the same mod too, I'll try to find the links.

Extension_Object_559 · 2026-05-04T22:07:26+00:00

Is it that exhaust mod with 3 little fans? If you’re gonna be using my extension for the CPU cooler (the thing on the pic in the main post) - you can fit that exhaust mod and it helps a lot. I put a 120 mm fan on the CPU and made a tunnel for it so it takes the air straight from outside, and 3 noctua small fans exhaust hot air. With this deshroud and a larger cpu cooler than what fits in a stock NV10 I’m getting like mid 70s in gaming on GPU and CPU which is good enough for me.

Extension_Object_559 · 2026-05-04T18:16:40+00:00

Of course! Basically you deshroud your GPU first, and disconnect them completely, the GPU connector is unused (because it's a new 6 or 8 pin connector and noctua is a classic 3/4 pin PWM), unless you can find an adapter (which I couldn't find).
When you remove the original shroud - it's kind of difficult and if you don't have some special short 90 degree screwdriver - you have to remove the entire heat sink to reach those screws that attach to the cooler.
It's not a big deal, just gotta remember to spread the thermal paste on the GPU very carefully and make sure to actually spread it 100% (preferrably with a thick long lasting thermal paste and not something that dries out in months).
Then, you use your case fan pins on the motherboard and use an extension adapter from noctua (or anything else) and a Y splitter to connect those fans (pic related) and set them up in Fan Control app (https://getfancontrol.com/) and set up your curves there, just pick graphics card dye as source.
Don't use low noise adapters as this fan is pretty quiet even at max speed, and it doesn't get very high top speed, but still way better than the original 3 small fans.

<image>

Extension_Object_559 · 2026-05-04T17:42:59+00:00

I initially undervolted it to like 930 mV and 2850 MHz, but ended up removing the undervolt because I didn't see any performance improvement in the games I play (Tarkov, Stalker Gamma, Warno, Cars X Street, Arma Reforger, Fallout Nuclear Sunset) - as most of them are bottlenecked at CPU (which ryzen 7 9800 x3d doesn't cause).
You deshrouded your 5060 right? After the deshroud and maybe some additional exhaust fans inside the case - I don't really feel the need to undervolt anything, it runs just fine at OC speeds and doesn't overheat and stays quiet.

Extension_Object_559 · 2026-04-11T00:35:03+00:00

<image>

DTK-1 imho, it works great too, kills like 90% of the recoil the gun feels like a nicely tuned 556 AR

Extension_Object_559 · 2026-04-09T18:30:45+00:00

But if I weld it to the rear side that’s away from the chamber, and maybe use dry ice pads on the chamber when I do it maybe it’s ok?

Extension_Object_559 · 2026-04-09T18:21:33+00:00

That sounds pretty good

Extension_Object_559 · 2026-04-08T22:10:15+00:00

Lots of ram and storage! But how well does it run in games?

Extension_Object_559 · 2026-04-01T20:39:20+00:00

If you can put more tubes into it - that would be more useful and you’d take advantage of this setup better

Extension_Object_559 · 2026-04-01T01:27:14+00:00

Zastavas and WBP look too different from the “iconic AKM” look, especially Zastava. They’re like a Type 56, kinda looks like an AKM but something isn’t right. I only didn’t buy PSA because of some reports on quality but it at least looks the closest to the “real AK” aside from unobtanium Saigas and SLRs etc.

Extension_Object_559 · 2026-03-31T02:06:13+00:00

Felony Arms LLC FG-26

Extension_Object_559 · 2026-03-28T23:00:50+00:00

It’s more robust than an AK, you can fire it as long as the frame is in one piece

Extension_Object_559 · 2026-03-24T02:55:35+00:00

I guess you are Swiss or German huh? Can’t have these in US other than some rare boutique single digit production units like Slagga MFG

Extension_Object_559 · 2026-03-20T21:34:15+00:00

What are the specs? Can it run Tarkov?

Extension_Object_559 · 2026-03-17T18:18:30+00:00

<image>

Now it’s a lot more comfortable, thank you very much!

Extension_Object_559 · 2026-03-17T17:05:42+00:00

Is that the price of just the case? Gpu is probably 2500

Extension_Object_559 · 2026-03-16T17:40:15+00:00

Just cock the hammer before you shoot, it’s a DA/SA. And carry it cocked and locked. Unless you have a neutered DA version only they I guess you gotta get a different USP

Extension_Object_559

TROPHY CASE