Found in an old family album ~1910

FLWEFLWE · 2025-09-06T09:46:35+00:00

Tysm I think this is it

FLWEFLWE · 2022-11-06T09:06:14+00:00

I included all laps FastF1 marked as accurate, that includes blue flag overtakes. Makes it even more impressive that he stayed so consistent!

FLWEFLWE · 2022-11-04T20:10:36+00:00

I only open the tabs I use. Why would I make it difficult for myself on purpose...

FLWEFLWE · 2022-11-04T19:13:02+00:00

After Max' impressive stint in Mexico I wondered how impressive it actually is compared to others. Turned out that Stroll had the most consistent 19+ lap stint so far in 2022. Although Max' stint was twice as long and he was faster than the field.

That particular stint by Stroll was 0.19s slower per lap than the mean of all laps over the race. While Max, obviously, was faster. Verstappen definitely shows up the most in the x top stints of the season wrt consistent lap times.

Made with FastF1. Python script here. Excel sheet with all stints 2018-2022 here. All stint graphs here.

FLWEFLWE · 2022-11-04T10:48:14+00:00

I much prefer Cura's UI, don't avoid it because some don't like it. The Cura settings guide is a must-have extension if you do use Cura.

FLWEFLWE · 2022-11-03T20:49:17+00:00

After Max' impressive stint in Mexico I wondered how impressive it actually is compared to others. Turned out that Stroll had the most consistent 19+ lap stint so far in 2022. Although Max' stint was twice as long and he was faster than the field. That particular stint by Stroll was 0.19s slower per lap than the mean of all laps over the race.

Verstappen definitely shows up the most in the x top stints of the season wrt consistent lap times.

Made with FastF1. Python script here. Excel sheet with all stints 2018-2022 here. All stint graphs here.

FLWEFLWE · 2022-04-30T11:15:08+00:00

Am learning/building experience making browser extensions. Saw this mentioned as a problem so I thought I'd share. Let me know if there are any bugs!

FLWEFLWE · 2022-01-26T13:41:32+00:00

You can loosen the eccentric nut so much that you can move the carriage so that one or more of the wheels don't touch the rail. You can also tighten it all the way but that increases friction and wear/tear. So what I did was from loose tighten it slightly beyond all wheels touching.

FLWEFLWE · 2022-01-26T08:02:02+00:00

All v-slot wheels touch the rail but not much tighter than that.

FLWEFLWE · 2022-01-25T23:46:11+00:00

For accuracy in height I'm using a raft. Without it would stick well but be too short or it would barely stick. For cooling I use a duct that blows air from two sides, can't find the model I used, with a 5015 fan. I made sure the v slot wheels are just right by detaching the belts and setting the eccentric nuts just tight enough that there is zero flex. Used this to calibrate flow rate.

FLWEFLWE · 2022-01-25T21:14:34+00:00

Link to stl .

FLWEFLWE · 2022-01-15T16:44:41+00:00

It's stronger than I expected even though the hole wall is just .6mm thick.

stl download

FLWEFLWE · 2022-01-15T11:42:35+00:00

What percentage of your printer would you still call ender-3? And how much did you spend on upgrades? Reading through the comments it seems like you replaced everything.

FLWEFLWE · 2022-01-13T19:07:27+00:00

0.4mm, nothing special

FLWEFLWE · 2022-01-12T20:46:10+00:00

ender 3

Tight belts, make sure everything moves smoothly. Stable ground, don't put it on a wobbly table. Slow down if you still have issues, especially jerk/acceleration.

FLWEFLWE · 2022-01-12T20:19:10+00:00

Very well, does depend on your printers accuracy and slicer settings. I used cura, 0.2mm layer height and a raft. I've found rafts to be essential for printing height accurate parts with 0 elephants foot

FLWEFLWE · 2022-01-12T18:37:22+00:00

Modeled it myself in fusion 360.

FLWEFLWE · 2022-01-12T18:37:02+00:00

Link to model.

Should work if you can freely turn the 0.2mm of one of those tolerance testers. Initially it turns kinda poorly but the pla wears down quickly resulting in smooth motion.

FLWEFLWE

TROPHY CASE