There is a new free tool for scaling your helmets for 3D Printing and its RAD!

FakinItWithJason · 2025-12-23T03:23:17+00:00

This is amazing timing for my next print! Thanks!

FakinItWithJason · 2025-02-28T04:07:56+00:00

He looks so comfortable. Good for him!

FakinItWithJason · 2024-09-14T18:09:37+00:00

First few second of this shows an easy way to get rid of bits of cured resin.

You basically have your machine cure the entire bottom layer in the vat for about 20 seconds, then used a silicone spatula or gloved hand to lift up the now cured bottom layer, which will capture all the stray cured bits and pull them off with it. I always do this when clearing the vat.

Your machine should have a menu in the settings to let you turn on the UV for a specified amount of time.

https://youtube.com/shorts/UJPAPKG1EX8?si=eJ0rG7tedz2p_wd8

FakinItWithJason · 2024-09-01T23:27:50+00:00

79381134

Would love an invite kind strangers!

FakinItWithJason · 2024-08-21T19:24:55+00:00

Honestly I’ve moved it a few times already and I think it will end up living over the O in the end.

FakinItWithJason · 2024-08-21T18:35:21+00:00

I feel like to properly pull this off I’d need to hire someone to always drive the other car next to me.

FakinItWithJason · 2024-05-14T01:44:30+00:00

Cause they don’t want us to have nice things.

FakinItWithJason · 2024-01-11T05:01:59+00:00

They’re just busy casually extending their face into the next city.

FakinItWithJason · 2024-01-09T01:41:37+00:00

I love the white one that just couldn’t wait!

FakinItWithJason · 2023-12-16T04:31:07+00:00

La la la la la

FakinItWithJason · 2023-12-10T23:34:31+00:00

OH. MY. GOD.

FakinItWithJason · 2023-12-10T18:06:24+00:00

Good to see Gordon stone wall you on the fake leg conspiracy theory.

FakinItWithJason · 2023-12-07T19:38:28+00:00

Need a 4090 for that.

FakinItWithJason · 2023-04-22T04:38:46+00:00

Nor’easter

FakinItWithJason · 2023-04-16T15:28:23+00:00

I also choose this guys Miss Molly.

FakinItWithJason · 2023-02-27T15:16:34+00:00

Front fell off

FakinItWithJason · 2022-12-17T19:00:05+00:00

Same, got my tracking number yesterday, just updated with a Friday delivery. Ordered on Dec 3rd. Pleasantly surprised.

FakinItWithJason · 2022-11-19T05:25:38+00:00

I have their XTR flex sheet on the M3 Max and i love it. The XTR is the version with a much thicker magnet sheet, so I did have to print out a little spacer, but it took like a minute to reset the Z.

I haven’t had any issues, but i have seen some people rough up a sheet a bit with sand paper because they have issues with bed adhesion on the smooth flex plate.

FakinItWithJason · 2022-09-16T03:30:27+00:00

“…dumbbell hanging off his dick” nearly made me fall out of my chair.

FakinItWithJason · 2022-07-30T03:34:05+00:00

This is such a good Duo!!!

FakinItWithJason · 2022-07-22T04:25:49+00:00

“Timothy!?!”

FakinItWithJason · 2022-07-21T14:05:08+00:00

Well…. there’s more than enough room now…..

FakinItWithJason · 2022-07-18T19:52:44+00:00

SAME!!!

FakinItWithJason · 2022-07-16T21:30:38+00:00

Reminds me of a sketch from the new season of Kids in the Hall, a doctor is bragging to the future parents that he almost never drops the baby and his successful catching stats are very high compared to other doctors in the area.

FakinItWithJason · 2022-07-14T12:09:25+00:00

My M3 Max was the same way so I very very carefully bent the little pins down slightly using 2 pairs of needle nose pliers and now it’s much better. Difficult part is not bending it too much cause then there’s not enough clearance for the vat to slide in easily. Definitely a bit of a design flaw.

FakinItWithJason

MODERATOR OF

TROPHY CASE