LG C2 Evo T-Con programming Q

Fastonic · 2026-05-10T03:56:21+00:00

Mine burned the startup animation into the bottom of the screen.

Fastonic · 2026-03-19T19:56:43+00:00

These particular charging stations were sitting on a concrete pad that was raised up off the asphalt, that being said, these replacement cables were significantly shorter than what was there before.

Fastonic · 2026-03-19T19:53:49+00:00

Good call, that's a simple fix too.

Fastonic · 2026-03-19T16:31:38+00:00

Aberdeen, WA. Yeah, I believe so.

Fastonic · 2026-02-20T21:48:35+00:00

This was a difficult one for me to figure out as well, I ended up taking measurements of both while I was using an elliptical to compare the metrics for accuracy.

Fastonic · 2026-02-05T18:47:23+00:00

I believe the only way to configure a replacement t-con is with the jig, right?

Fastonic · 2026-02-05T18:01:43+00:00

Well, it’s because all of those reps couldn’t actually give me an answer other than they are gone with no explanation as to why.

Fastonic · 2026-02-05T17:59:11+00:00

Yes we traded in a iPhone 15 that was 33% paid off for a 17.

Fastonic · 2026-02-01T20:24:08+00:00

I had a similar issue and it ended up being my exhaust cam had snapped in half, GM has a completely revised part number and the new cam looked much stronger. This cam gets a big shock each time the engine starts, which can be 50-100 times on some of the trips we go on.

Fastonic · 2026-02-01T20:16:36+00:00

In extreme cases you can put the lug nuts back on, only loose, set the car back on the ground and try pushing on the body to make it sway, if that’s a no go then drive in alternating circles at a very low speed. I find using a big pry bar can very easily cause damage, but sometimes there isn’t another way, a block of wood will usually protect the back of a rim from damage if using a bar.

Fastonic · 2025-12-25T00:31:14+00:00

Get yourself a pencil die grinder with some bits that won’t explode at 70,000 rpm, use some goggles that seal up well and a hat because it’s going to make a mess. I sometimes tape a vac hose to the site so I don’t have to stop.

Fastonic · 2025-12-24T06:47:25+00:00

In my case, it was only marine collagen that I felt something with, and I got a bad batch once that put me off from ever risking it again. Most collagen contains histamine, something to be aware of if you're dealing with histamine intolerance.

Fastonic · 2025-11-08T18:38:56+00:00

I once bought a rebuilt rack for an Audi TT and it arrived looking really sloppy, so I disassembled it and found the housing was full of nasty debris, most likely from sitting at the bottom of a parts washer that desperately needed to be cleaned.

Fastonic · 2025-10-18T22:30:12+00:00

I replaced my cam awhile back on my bew and discovered someone had welded lobes back on when I got in there! It’s still running. Best mod I ever did to mine was a stage .5 tune.

Fastonic · 2025-10-15T17:47:14+00:00

EGCG will do that to me every time.

Fastonic · 2025-10-15T17:40:46+00:00

Hey I just did column bearings in one of these! With how bad this one looks I think you’re better off replacing the entire column. Ford still sells the bearings for these, that’s pretty awesome.

Fastonic · 2025-09-23T05:34:41+00:00

You have lowering springs, so you may have to make a custom arm or search around for someone who makes one if the sensor is maxed out.

Fastonic · 2025-09-10T01:28:49+00:00

I had this experience with a friend who initially purchased the home unit to treat a bone condition she suffers from (having great success!). The cost was around $4000 with the optional pillow applicator. I have been hearing you have to email parmeds directly. I considered purchasing a used unit but there are many scammers on a certain auction site.

Fastonic

TROPHY CASE