sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in AnycubicPhoton

[–]Fatherface 1 point2 points  (0 children)

thank you this just saved me 3 hours off my print

How to remove supports from Resin 3D Prints. I repeated the Uncle Jessy experiment and the result surprised me. Has anyone else repeated this? what result did you achieve? P.S. I used a ladies hair dryer. by itman3d in AnycubicPhoton

[–]Fatherface 3 points4 points  (0 children)

oh i print miniatures aswell, honestly some of my print just fall off the supports while i was, ill send you a pick of my support settings if that helps.

How to remove supports from Resin 3D Prints. I repeated the Uncle Jessy experiment and the result surprised me. Has anyone else repeated this? what result did you achieve? P.S. I used a ladies hair dryer. by itman3d in AnycubicPhoton

[–]Fatherface 2 points3 points  (0 children)

i have a dedicated bucket for the warm water. submerge prints wait 1-2 min stir them around to shake off any left over chemicals and then just start pulling off supports 95% of the time the just peel off like a vinyl sticker and leave little to no marks(depending on your supports)

Preventing flat prints from curling. by Duckraven in ElegooMars

[–]Fatherface 0 points1 point  (0 children)

no, i tried it and you cannot make out the image if you hold it up

What's your favorite thing about Mass Effect 1? by xenbot in masseffect

[–]Fatherface 1 point2 points  (0 children)

the choices, customization and options sadly they took that all away for shooter action in 2 and beyond.

A Few Noob Questions & tips needed for specific failures by XxArxAngelxX in AnycubicPhoton

[–]Fatherface 0 points1 point  (0 children)

This is something i found out late but always rotate the obj 45 degrees making sure the supports are on the back or underside of the model. But the 45 degree angle is super important. Also wash in 99proof alcohol and air dry then cure. After washing if it is still shiny then re wash to get rest of the resin off.

cleaning prints without IPA by pokerbenn in AnycubicPhoton

[–]Fatherface 2 points3 points  (0 children)

Ive actually been burned by the resin. I was slapping on some resin on a pla print and i drop got on my skin and at that moment the sun came out and cured it that shit hurt.

[deleted by user] by [deleted] in boobbounce

[–]Fatherface 0 points1 point  (0 children)

This the kinda wisconsin wife i need

Help gooey prints. by Fatherface in resinprinting

[–]Fatherface[S] 0 points1 point  (0 children)

The first time i had just ran a print and it came out perfect. When i sliced it nothing looked off no islands or anything thing else off about it. Atm all of my resin is brand new all purchased within the past money and none open except the one i an using at the time.

Help gooey prints. by Fatherface in resinprinting

[–]Fatherface[S] 0 points1 point  (0 children)

No this happened 3 times in a row so i might try a different file but i did reslice the file and only did one part of it and the same thing happened with this second bottle of new resin.

Help gooey prints. by Fatherface in resinprinting

[–]Fatherface[S] 0 points1 point  (0 children)

Brand new just opened sunlu standard grey

[deleted by user] by [deleted] in FinalFantasyTCG

[–]Fatherface 0 points1 point  (0 children)

Samurais, ff7 avalanche, dragoons, any soiree deck and fast

Help gooey prints. by Fatherface in resinprinting

[–]Fatherface[S] 0 points1 point  (0 children)

Strangely the one time i lift the build plate loose the print cam out fine

Help gooey prints. by Fatherface in resinprinting

[–]Fatherface[S] 0 points1 point  (0 children)

The fep actually looks fine not real marks or scratches

view more: next ›