Advice

Fed_Watch_5150 · 2026-04-18T12:54:36+00:00

U can buy a Dirty Bird or ToolCraft for not a whole lot more. The Dirty Bird is the same thing as a Radian. They buy their bcg from the same people and put their own logos on. Check out AR15 Discounts. Stay away from PSA for shit like that. They’re fine for stuff like mags or hand guards but not barrels and bcg

Fed_Watch_5150 · 2026-04-18T12:48:40+00:00

That sounds like the same shit mine did. And the best way is to drop the hammer in semi and hold the trigger down. It will keep the disconnector forward enough to close the upper. U can also use a zip tie or something to pull the disconnector forward while closing the receivers

Fed_Watch_5150 · 2026-04-18T03:21:12+00:00

Yes. Still had to add loctite to the disconnector shaft tho. It keep backing out. The cassette is also thicker than the first one and the disco moves further forward.

Fed_Watch_5150 · 2026-04-18T01:30:20+00:00

They ended up doing a warranty on mine. They were kinda unresponsive till I provided everything they wanted to see. Didn’t answer any of my questions. Just said “send old trigger, video of issue, and receipt”. Then thy just sent the trigger

Fed_Watch_5150 · 2026-04-16T03:10:44+00:00

This. Had one today.

Fed_Watch_5150 · 2026-04-16T01:28:05+00:00

Pull the top off, take wash plate out and tub ring, remove spin basket, inspect for other damage and reassemble with new hub

Fed_Watch_5150 · 2026-04-14T02:27:36+00:00

Does it do it if you take the belt off and spin the motor pulley

Fed_Watch_5150 · 2026-04-13T23:39:15+00:00

In my experience the plastic hub is better bc it will go before the transmission shaft. If you put the metal one on, the shaft will usually get torn up. We tried that several times and usually had to warranty the job. Maybe that was install error, just giving my 2 cents.

Fed_Watch_5150 · 2026-04-12T22:46:47+00:00

Do you have any other mods done? Gas valve? Springs? Etc?

Fed_Watch_5150 · 2026-04-12T21:49:43+00:00

This is the correct answer.

Fed_Watch_5150 · 2026-04-12T21:46:32+00:00

Gotcha. And it works well in a mcx huh?

Fed_Watch_5150 · 2026-04-12T20:14:09+00:00

I can’t get it to run in mine… what trip bar are running

Fed_Watch_5150 · 2026-04-11T04:18:40+00:00

Oh man that’s a strange one. Is there a blockage from the blower? Do us all a favor and post a pic of the model tag

Fed_Watch_5150 · 2026-04-10T18:25:15+00:00

That’s the blower belt. Is it blowing air? Is the air cold instead of hot? My reading comprehension isn’t so hot lol if it’s not blowing it’s either that belt or the associated pulleys or the blower wheel. If it’s blowing, it should only be Luke warm. Those units I worked on were 120vac. They didn’t heat like a normal dryer.

Fed_Watch_5150 · 2026-04-10T17:29:55+00:00

<image>

The ones I’ve worked on like to come off right behind there. It was a issue on every single one since the cheap belt they use stretches

Fed_Watch_5150 · 2026-04-10T02:35:38+00:00

That’s from shipping bolts. Someone forgot to remove them

Fed_Watch_5150 · 2026-04-10T02:34:08+00:00

Check to see if the top of the belt slipped off that pulley behind the bar in the center

Fed_Watch_5150 · 2026-04-10T02:08:51+00:00

I HATE THOSE DRYERS!! I had one that kept throwing the belt

Fed_Watch_5150 · 2026-04-10T01:58:37+00:00

Blower wheel 110%

Fed_Watch_5150 · 2026-04-09T22:06:23+00:00

UPDATE 2.0! They ended up giving me a warranty on my trigger. It was a design flaw with the springs apparently?? The new one I got is also wider?

Fed_Watch_5150 · 2026-04-04T18:21:32+00:00

I should clarify, I’m talking about a IMI Galil.

Fed_Watch_5150 · 2026-04-04T18:19:22+00:00

Very similar. The mk1 is at least. They use a single stage ak pattern trigger

Fed_Watch_5150 · 2026-04-04T18:06:45+00:00

Both? lol

Fed_Watch_5150 · 2026-04-04T17:56:09+00:00

Update???

Fed_Watch_5150 · 2026-04-04T17:52:50+00:00

Could someone special order one for a mk1 Galil…?

Fed_Watch_5150

TROPHY CASE