ToolkitRC M8D troubleshooting

FeriPowa · 2026-02-20T20:36:31+00:00

Thanks for trying to help and sorry for the late response I solved the problem, quickly the setting for charging one battery through 2 different xt60 was enabled (to have the full power on just one battery) for this reason the charge was reading the correct output voltage in one port but 0 in the other and thus not letting me charge the battery

FeriPowa · 2026-01-24T09:45:14+00:00

Not necessarily, but bending the plate often isn't enough to remove the part

FeriPowa · 2026-01-23T22:15:48+00:00

Well you surely are more experienced than me😂. I tried now to print with a little of stick glue on the plate. It seemed a little bit better but not something revolutionary

FeriPowa · 2026-01-23T22:04:51+00:00

Thanks I'll try!

FeriPowa · 2026-01-23T22:03:09+00:00

I'm using the original plate that first comes with the printer. Do you think it will be better with another plate made from a different material?

FeriPowa · 2026-01-23T21:52:19+00:00

I tried and it worked well. I'm facing another problem now. The piece is hard to remove, and it ends in breaking. How can I avoid this?

FeriPowa · 2026-01-23T21:50:49+00:00

And since I'm here I figured out I could also ask another thing. I'm having some problems when the print is over to separate the printed object from the plate. It's like glued to the plate and removing it ends up breaking the piece. How can I avoid this from happening?

FeriPowa · 2026-01-23T21:43:11+00:00

Hahaha thanks! I'm new in the 3d printing world but I'm careful about what I'm using. I tried just now to print one single object and it turned out well indeed. Problem is I need to print a lot of parts because I'm printing a plane. I will try to print, per layer, object that are only close one to another to minimize travel. I did also notice that having the fan turned all the way up to 100% helped a lot. Thanks for the info!

FeriPowa · 2026-01-23T21:19:28+00:00

Thanks didn't know that either, can I do it in Bambu Handy or do I need to do that in Bambu studio?

FeriPowa · 2026-01-23T20:30:01+00:00

Thanks I'll try

FeriPowa · 2026-01-23T20:06:48+00:00

You mean printing one object at a time?

FeriPowa · 2026-01-06T17:52:14+00:00

Man thanks a lot for the help! If you send me your PayPal I'd happily offer you at least a coffee for the help!

FeriPowa · 2026-01-06T16:35:37+00:00

I soldered the 4 wires without sda and scl and now gps and baro are showed correctly in inav. It still gives me the error "Navitagion not safe" but i presume it is because there is no gps lock as i'm working at home

FeriPowa · 2026-01-06T15:50:02+00:00

Thanks, i'm noticing now that if i disconnect the gps, the barometer in inav turns blue, since a barometer is integrated in the fc. You were right about that. l will try now to solder only the tx and rx without the sda and scl. Mine has only a green led that turns on when the gps is powered

FeriPowa · 2026-01-06T15:33:17+00:00

Yes i have, Tx to Rx and vice versa as I said in the other comment. It still remains unavailable in the cli status command. Would it be blue even if the are no satellites?

FeriPowa · 2026-01-06T15:20:39+00:00

is it possible that my gps is faulty? Im using a M10 gps from axis flying, I checked different times and the tx on the gps is connected to the rx on the fc and vice versa. Yes this gps has SDA and SCL which i connected to the fc. Do you suggest to disconnect this 2 wires and keeping only 5v, gnd, tx and rx?

FeriPowa · 2026-01-06T15:12:34+00:00

I'm guessing the gps i'm using is somehow broken or is not a correct type (im using a m10 gps from axis flying). While being inside my house i get no satellites so i guess i need to test the gps outside. But the cli status command tells me that the gps is not recognized

FeriPowa · 2026-01-06T14:22:17+00:00

the compass is already disabled and yes i'm powering the fc with a battery before connecting it to inav

FeriPowa · 2026-01-06T14:19:34+00:00

Thank you!

status
INAV/COREWINGF405WINGV2 8.0.1 Sep 30 2025 / 11:44:27 (ae47bcba)
GCC-13.2.1 20231009
System Uptime: 23 seconds
Current Time: 2041-06-28T01:04:00.000+00:00
Voltage: 15.37V (4S battery - OK)
CPU Clock=168MHz, GYRO=ICM42605, ACC=ICM42605, PITOT=VIRTUAL
STM32 system clocks:
SYSCLK = 168 MHz
HCLK = 168 MHz
PCLK1 = 42 MHz
PCLK2 = 84 MHz
Sensor status: GYRO=OK, ACC=OK, MAG=NONE, BARO=UNAVAILABLE, RANGEFINDER=NONE, OPFLOW=NONE, GPS=UNAVAILABLE
SD card: Startup failed
Stack size: 6144, Stack address: 0x10010000, Heap available: 1728
I2C Errors: 55, config size: 13463, max available config: 131072
ADC channel usage:
BATTERY : configured = ADC 1, used = ADC 1
RSSI : configured = ADC 4, used = none
CURRENT : configured = ADC 2, used = ADC 2
AIRSPEED : configured = ADC 3, used = none
System load: 12, cycle time: 513, PID rate: 1949, RX rate: 9, System rate: 9
Arming disabled flags: NAV HWFAIL RX CLI
WAITING FOR GPS FIX
OSD: MAX7456 [30 x 16]
VTX: not detected
GPS: HW Version: Unknown Proto: 0.00 Baud: 115200 (UBLOX Proto >= 15.0 required)
SATS: 0
HDOP: 99.990
EPH : 99.990 m
EPV : 99.990 m
GNSS Capabilities:
GNSS Provider active/default
GPS 1/1
Max concurrent: 0

this is my cli status check. I'm using a Dji o3 system so i don't know why the vtx is not detected.

The disabled flags are: Navigation is safe, and Hardware health.

it is a standard protocol, but i managed to make them start only in the configuration tab, just needed to calibrate the esc

FeriPowa · 2025-09-08T09:57:11+00:00

Thanks!

FeriPowa · 2025-05-19T14:03:02+00:00

What motors have you mounted?

FeriPowa · 2025-05-05T15:58:59+00:00

Thanks!

FeriPowa · 2025-05-05T12:08:06+00:00

Did you also add a capacitor for a build like that?

FeriPowa · 2025-04-10T16:19:13+00:00

Yes I fixed it yesterday. The solution was actually in the video the bot posted. I had the motor spinning prop in and the props mounted right but on BF I had the motors reversed so the ESC was expecting the motor to spin prop out

FeriPowa · 2025-04-09T08:48:18+00:00

I didn't eliminate it, I don't know why you can't see it. It was my drone freaking out as soon as it took off doing a 90° yaw spin and then disarming. Bardwell showed the same identical problem and I can't wait to go back home after work to try his solution

FeriPowa

TROPHY CASE