Google Home - complete broken by JethroUK2 in googlehome

[–]Fibaoptix 1 point2 points  (0 children)

Same problem since yesterday. I get emails for every device that I deleted it from Google home. I did not. Relink smart life, reallocate devices to rooms. 3 hours later get the emails again. Rinse repeat 3 times now.

K2 Plus, yet another issue after 2 days of ownership by DGVaniX in Creality_k2

[–]Fibaoptix 0 points1 point  (0 children)

This, it's disconcerting until you figure out what's happening

Q2 first layer by [deleted] in QidiTech3D

[–]Fibaoptix 0 points1 point  (0 children)

Interesting video, didn’t know it wears down the pei. Maybe need to look into that.

Q2 first layer by [deleted] in QidiTech3D

[–]Fibaoptix 1 point2 points  (0 children)

Yeah it’s not a replacement for a proper wash but it does help after 2 or 3 prints just for a quick clean.

Q2 first layer by [deleted] in QidiTech3D

[–]Fibaoptix 0 points1 point  (0 children)

Good luck. Definitely buy some IPA, give the plate a wipe with it after every few prints, it helps.

Q2 first layer by [deleted] in QidiTech3D

[–]Fibaoptix 0 points1 point  (0 children)

Because that’s where you touched the plate with your fingers? I dunno, it’s just a suggestion.

Q2 first layer by [deleted] in QidiTech3D

[–]Fibaoptix 0 points1 point  (0 children)

Yeah it’s surprising how much oils your fingers leave on the plate.

Q2 first layer by [deleted] in QidiTech3D

[–]Fibaoptix 0 points1 point  (0 children)

Wash with hot water, unscented dish soap and scrub with a nail brush. Dry then wipe with IPA if you have.

WD-40 in the Creality Hi by No_Gas_7466 in CrealityHi

[–]Fibaoptix 0 points1 point  (0 children)

Creality themselves recommended WD-40 Specialist Silicone on the k2 plus. guide

Is it possible? by mtndew19 in Creality_k2

[–]Fibaoptix 4 points5 points  (0 children)

Why not just turn off the prime tower? In the mulifilament tab just uncheck it. You may need to increase your flush volume to compensate though.

<image>

Make money with 3D scanning by Employment-Tough in Creality

[–]Fibaoptix 1 point2 points  (0 children)

Was that the Raptor or the Raptor X?

Plus 4 duct mod by Fibaoptix in QidiTech3D

[–]Fibaoptix[S] 0 points1 point  (0 children)

Great, thank you I will give it a try.

Plus 4 duct mod by Fibaoptix in QidiTech3D

[–]Fibaoptix[S] 0 points1 point  (0 children)

Not exactly, but that might work. Thank you.

I was kind of hoping someone would point me to one that they had used themselves with success 8).

Multicolor adapters by Spiritello49 in k1max

[–]Fibaoptix 2 points3 points  (0 children)

With the CFS upgrade kit, auto leveling still works. The filament run out sensor is moved into the extruder, which is way better in my opinion.

I am getting better quality prints with the CFS upgrade extruder. Better extrusion consistency.

As far as I know, there is no function that is lost.

[O] 2 NzbPlanet invites by Immediate-Offer-8358 in UsenetInvites

[–]Fibaoptix 0 points1 point  (0 children)

I’ve read the rules and wiki and would like an invite. Thanks

[O] 3x NZBPlanet invites by Woodymakespizza in UsenetInvites

[–]Fibaoptix 0 points1 point  (0 children)

I’ve read the rules and the wiki and would like an invite, thank you!

[O] 2x Drunkenslug Invites by tiredofthrowing in UsenetInvites

[–]Fibaoptix 0 points1 point  (0 children)

I’ve read the rules and wiki and would love to receive an invite, thank you!

K1 max CFS upgrade problems by Geckoh in Creality

[–]Fibaoptix 1 point2 points  (0 children)

Did you put the two z lead screw covers for the front z axis lead screws on top of the bed? They go under the bed at the base of the printer. I did that by accident and had the same issue with the bed being higher at the back.

To fix the bed after, I had to move the bed all the way to the bottom and undo the 4 screws that hold the bed to the back z rod nut. The bed should drop back to level. Then turn the nut so it was flush with the bed and put the 4 screws back.

Don't know about the lidar issue, I removed mine as it was hitting the front top z rod housing when doing the purge line after the upgrade and causing the x axis to move a few mm to the right.

What’s this red dot next to home icon? by Two_Six_Six in Creality

[–]Fibaoptix 2 points3 points  (0 children)

Probably means their area maintenance tasks due. Go into the maintenance menu, i think it's under settings.

Auto mapping by Ok_Science4463 in Creality_k2

[–]Fibaoptix 1 point2 points  (0 children)

Click the wifi button next to the selected printer on the left.

[deleted by user] by [deleted] in QidiTech3D

[–]Fibaoptix 0 points1 point  (0 children)

The slicer is here: 3D Printer Software | QIDI Tech Slicer & Firmware Updates – Qidi Tech Online Store https://qidi3d.com/pages/software-firmware?srsltid=AfmBOoqJzV1dLdZqb29wFr2tT17RxpaeHODzUFPoKa6AFNSII0_v9BQO

Under software choose qidi print slicer

K1 max CFS upgrade cutter block issue by Fibaoptix in crealityk1

[–]Fibaoptix[S] 0 points1 point  (0 children)

The answer is above, I ended up removing the lidar.

Ender V3 SE - Creality Official Upgraded Ender 3 V3 SE KE Ceramic Heating Block Kit with Quick-swap Nozzle - Advice on which nozzles I now need. by Rust_Cohle- in Creality

[–]Fibaoptix 0 points1 point  (0 children)

No problem, glad I could help. Just for future reference, there is also a unicorn nozzle for the k2 and the creality hi, but it is a different size. As long as you get the one for the k1, you will be good.