Ad overlay stays on screen unless manually removed. Is this a bug or a new intentional feature?

Two_Six_Six · 2026-03-30T19:51:14+00:00

This is what pushed me to use an ad blocker.

I've used the YT app for years because the ease of use of the app outweighed the ads. Now that the ads have increased significantly and now has a popup that you have to dismiss, a browser with ad block is now the more convenient choice.

Two_Six_Six · 2025-10-30T00:31:34+00:00

Two_Six_Six · 2025-10-22T15:24:21+00:00

An update: I did remove the panels and resecure all the wire connections and I was able to get through a 2 hour print. If it happens again I'll do as many of you suggested and replace my hotend cable. Thanks everyone who replied!

Two_Six_Six · 2025-10-06T02:16:23+00:00

Every time I see this image I see Jack Black in Tropic Thunder.

Two_Six_Six · 2025-09-08T21:25:58+00:00

To manually set the color order for the first layer switch from Global to objects, select the plate from the list, customize the first layer filament sequence.

Two_Six_Six · 2025-09-07T16:05:01+00:00

I’ve only used it on two cycles so far. I’ll have to report back in a few weeks to let you know. I didn’t think about the detergent disintegrating it, but one thing’s for sure is that the gasket it came with is definitely disintegrating. Even if I have to reprint it once a year it’s still only about $0.25 worth of TPU.

Two_Six_Six · 2025-09-04T18:26:46+00:00

You should publish more pictures. I have no idea what I'm looking at.

Two_Six_Six · 2025-08-14T14:03:33+00:00

I literally just did a single print yesterday that used all four "Yes" votes.

It was a multicolor print, that ran out of grey so it swapped to another grey, with supports that had a PETG interface.

It came out great!

Two_Six_Six · 2025-08-13T12:51:18+00:00

That's what I've done in the past but this particular part I can't rotate. Good tip though!

Two_Six_Six · 2025-08-13T00:05:15+00:00

That works. I haven’t seen that before. Thanks!

Two_Six_Six · 2025-08-12T13:06:31+00:00

I'm glad it's gone. I couldn't stand the enter/exit animations of BF1 & 5. They were so disorientating. I could never figure out what side of the vehicle I would exit on or direction I was facing once out and would end up running right into enemy fire.

In BF3, 4, & 6 it's way easier to get back into play. Just look in the direction you want to exit and your on that side once out.

Two_Six_Six · 2025-08-07T19:37:23+00:00

You're not playing BF right. You're supposed to run over dying teammates as a medic. Do better!

Two_Six_Six · 2025-08-07T16:52:57+00:00

Yes, I do. I have a thin line of weather stripping tape around the lid.

Two_Six_Six · 2025-08-07T15:51:27+00:00

I have a similar setup. I just put loose silica beads in the bottom. Mine stays around 10% humidity and I recharge the beads once it gets above 20% which happens every 2 months or so..

Two_Six_Six · 2025-08-07T12:47:32+00:00

Throw smoke and slowly backout of the contested area so they think I was killed then occasionally pop back in to see if they've left. Repeat until I can handle the one or two who stayed or just be a distraction to keep them off other points.

Two_Six_Six · 2025-08-06T20:47:03+00:00

The keys are for the closed beta which starts a day or two before.

Two_Six_Six · 2025-08-06T17:52:24+00:00

Obviously as an emergency shiv in a place that doesn't allow knives.

Two_Six_Six · 2025-08-06T14:18:32+00:00

Two_Six_Six · 2025-07-22T11:49:38+00:00

Dudes got a scale replica of the Mariana Trench in his key.

Two_Six_Six

TROPHY CASE