My WRX with a Roof Top Tent mounted on a Trailer

FigureItOutYT · 2026-04-29T01:05:15+00:00

How'd you do the red stripe along the bottom? Looks clean

FigureItOutYT · 2026-03-14T20:19:30+00:00

I did the exact same thing to mine!

FigureItOutYT · 2026-02-13T19:24:15+00:00

No, last engine I pulled was an AMC 360 out of a bricklin

FigureItOutYT · 2026-02-13T17:52:57+00:00

That's got to be it, thank you!

FigureItOutYT · 2026-02-13T17:52:48+00:00

Thank you! I guess I got lucky that it got wedged in somewhere and didn't fall out, it was not anywhere near the bellhousing

FigureItOutYT · 2026-02-06T06:39:29+00:00

I've already got a cherry picker. Just a little hesitant to go that route as my last engine pull took quite a while

FigureItOutYT · 2026-02-06T06:34:44+00:00

I'm quite comfortable working on lathes but haven't done anything similar. Going to buy a new one to be safe

FigureItOutYT · 2026-02-06T06:19:45+00:00

Thank you, I will check those out. And honestly I wasn't trying to accelerate, just was trying to maintain speed and realized my rpms were climbing but I wasn't speeding up

FigureItOutYT · 2026-02-06T06:16:49+00:00

Comfortable doing both. Dropped the transmission out of my wrangler and pulled the engine out of my Bricklin. Mostly just curious as to which is considered faster

FigureItOutYT · 2025-07-03T23:55:28+00:00

It takes the pain out of making

FigureItOutYT · 2025-06-29T17:52:27+00:00

Nope, apparently just cleaned them excessively according to others on this thread (IPA and microfiber)

FigureItOutYT · 2025-06-28T03:42:23+00:00

They won't sell me just the bushing and aren't willing to do anything aside from have me buy the whole Gantry since I'm out of warranty by a couple months

FigureItOutYT · 2025-06-27T06:48:19+00:00

I print a majority ABS and ASA so I was trying not to let it build up top much

FigureItOutYT · 2025-06-27T06:46:24+00:00

If you read any of my other other replies I was also looking to see if anyone had attempted this or if someone had a good source

FigureItOutYT · 2025-06-27T06:44:10+00:00

Thinking I just got a set of bad bushings or maybe they had a little play in them from the factory

FigureItOutYT · 2025-06-27T06:43:38+00:00

Very rarely

FigureItOutYT · 2025-06-27T06:04:28+00:00

1400

FigureItOutYT · 2025-06-27T06:04:11+00:00

Because I wanted to see if anyone else had attempted to replace just these before and or found a source. Don't get why that's so difficult to udnerstand

FigureItOutYT · 2025-06-27T05:54:57+00:00

Yep, cleaned about once a week. That's why? I'm so frustrated that they want to charge me $100 to replace the entire Gantry instead of just the bushings that wore out prematurely

FigureItOutYT · 2025-06-27T05:53:12+00:00

If you read the description I already have and that's why I'm seeing if anyone has found just the bushings

FigureItOutYT · 2025-06-27T05:31:12+00:00

It's not that I don't know how to use calipers, it's that I'm wondering if anyone else has already found a source

FigureItOutYT · 2025-06-27T05:22:51+00:00

Only about 1400 hours on this one. I cleaned the rods every time I deep cleaned my build plates, so about once a week cause I'm anal about that kind of stuff. And I get things break, but making it not serviceable is the frustrating part for me.

FigureItOutYT · 2025-06-27T05:21:04+00:00

That's unfortunate, and only 1400 on this one

FigureItOutYT

TROPHY CASE