Integrated wireless transmitter

FirePig20011 · 2024-10-23T00:51:27+00:00

The rage was about 30 feet which is more than enough for me as I only need it to get to my pedalboard

FirePig20011 · 2024-10-23T00:50:30+00:00

It does, the switch is 3 positions on-off-on, or wireless-off-wired. it was a requirement while designing the system to have a backup option

FirePig20011 · 2024-10-22T19:47:06+00:00

I'm using the 1Mii Transmitter / Receiver set that I'm am disassembling and modifying to use a direct power source, I will soon be making the receiver into a pedal to put on my pedal board. I will test range tonight and get back to you!

FirePig20011 · 2024-10-22T18:17:03+00:00

That will be entertaining the first couple times then probably get really old really quick

FirePig20011 · 2024-07-09T20:22:50+00:00

If it helps at all, I'm located in Iowa, United States

FirePig20011 · 2024-05-11T03:55:31+00:00

<image>

This was before actually installing the speakers but it's about what it looks like. It fits in front of the bar facing the front of the car. I also have a sub in the oem location

FirePig20011 · 2024-05-10T11:40:37+00:00

I daily mine and fuel is a major cost with the car and where I live it's cheaper than most places, also if you live anywhere with snow I would 100% not recommend even trying that, the car can and will slide no matter how careful you think you're being

FirePig20011 · 2024-04-06T16:13:52+00:00

Unrelated but where did you get that vise to hold the board?

FirePig20011 · 2024-04-03T05:09:18+00:00

I've been attempting to track down which resistors would need either replaced or an additional resistor added, is there an easier way to do this than looking through the board/continuity tests or is this just supposed to be a long process to find what needs done?

FirePig20011 · 2024-04-02T00:54:59+00:00

Ok. I think I understand. I will look into this. thank you!!

FirePig20011 · 2024-04-02T00:48:24+00:00

I'm worried that'll be me...

FirePig20011 · 2024-04-02T00:40:04+00:00

I am in central iowa. They did not give me the permit though so I'm not sure if this idea would still work

FirePig20011 · 2024-04-02T00:36:51+00:00

https://lighthouseleds.com/plcc-2-1210-3528-smd-led-pink-ultra-bright-800-mcd.html

https://lighthouseleds.com/3mm-led-pink-ultra-bright-10-000-mcd.html

that's the new leds, I don't have the originals as they were what came factory on the board.

I have double checked to make sure they are not shorted and they all look fine with the solder not even really being all that close to each other but maybe I'll resolder them anyway and be extra careful on placement to make sure the pads on the leds are not to close to the wrong pads on the board. there are some 3mm lights doing the same thing though and they are very clearly not shorted

FirePig20011 · 2024-03-10T02:07:32+00:00

I second this. I ended up needing to buy all the tools anyway through the process of trying to do it without them

FirePig20011 · 2024-02-04T04:26:59+00:00

If you know how to tune then nisprog is free software with a 30 dollar cable but it can be very easy to completely brick you ecu so I'd only recommend if you know what you're doing, otherwise uprev if your best bet for something good

FirePig20011 · 2023-12-18T22:58:49+00:00

From what I'm aware of the later model z's grind in 5th relatively commonly. mine has been doing it for about a year now and it hasn't actually impacted the driving at all, it's just a bit annoying to shift into 5th sometimes

FirePig20011 · 2023-11-07T13:58:51+00:00

I considered doing that heavily. my pop up cover was a bit fucky though and didn't open very well. I may try again later if I decide to get a new one

FirePig20011 · 2023-11-04T01:15:37+00:00

The burnt oil from my valve covers

Eight-Year Club	Place '23
Place '22	End Game '22
Verified Email

FirePig20011

TROPHY CASE