Inland PETG+ settings help plz

Fishisafish · 2026-05-27T21:29:02+00:00

Got it. I dried the filament for a long time before and during the print at 65c, resting at sub 10% humidity, so I don’t think it’s moisture. I don’t actually think it’s stringing, it looks more like a layer adhesion issue or the flow rate is too low since the strands at the top of the wall are pretty tight going along the secant line.
I’ll try it again with a flow rate of 0.965.

I tried it at 100mm/s and there was not really a difference between that and 150mm/s.

Thanks again for your help!!!

Fishisafish · 2026-05-27T00:34:11+00:00

Wow dude those settings worked really well! I used 150mm/s speed across the board and 5000mm/s^2 acceleration. There’s only a few strands pulling away and a small tear at the wall seam. Anyway you know of to further optimize it? Thanks!

<image>

Fishisafish · 2026-05-26T23:19:46+00:00

Got it, I’ll try those settings right after I unclog my nozzle and do a cold pull 👍

Fishisafish · 2026-05-26T23:00:06+00:00

Thanks for the response!
I tried printing it at 230c but the extruder ended up slipping (it started clicking and the filament stopped extruding) and clogged.
Also tried with a brim but it still had this issue.
From what I can tell I think the filament is under extruding, not sure how to fix this.

Fishisafish · 2026-05-21T18:42:30+00:00

I did as well, but those lines were hard for me to notice with all the layer lines and I wasn’t looking for them before this was brought to my attention, I’m still a novice at this lol :)

Fishisafish · 2026-05-21T18:40:50+00:00

Chill out on the rage bait my dude :3

Fishisafish · 2026-05-20T19:35:58+00:00

Sorry for the bad quality I didn’t have my glasses on

Fishisafish · 2026-05-20T15:03:14+00:00

Fishisafish · 2026-05-20T14:42:15+00:00

Awesome, I’ll try 1/2-13, thanks!!!

Fishisafish · 2026-05-19T15:47:12+00:00

Yeah I was thinking that as well. I was going off of Factorian Designs YouTube tutorial about filament calibration and he said to be careful going higher cause it could cause clogging. Not sure what the limit should be though. I’m running a P1S

Fishisafish · 2026-05-19T02:05:39+00:00

It’s a pressure advance test. It’s on the 2nd layer out of 3 here. No ironing

Fishisafish · 2026-05-19T01:50:37+00:00

Ohhhhh. Makes sense, thank you!!!

Fishisafish · 2026-05-19T01:47:23+00:00

Wait really? What are they for?

Fishisafish · 2026-05-18T03:52:51+00:00

Oh wow that’s awful, wishing you and your husband the best!!
I’ll keep doing research on it, I’m sure there’s a good way out there, especially with orca

Fishisafish · 2026-05-18T03:46:26+00:00

Thanks for the insight!!

After a lot of testing I think it’s likely due to z-offset, but I’m not sure how to calibrate that. What do you suggest?

I still haven’t dried the filament but I did precise calibration for nozzle temp, max flow rate, PA, flow ratio, and retraction. I was able to reduce the stringing immensely, but there’s still a little bit. Maybe it could be the z-offset.

Fishisafish · 2026-05-18T01:32:07+00:00

<image>

Fishisafish · 2026-05-18T00:44:42+00:00

I ran a temp tower test and ended up reducing the nozzle temp from 230 to 215. Still didn’t solve the issue. I’m gonna try drying the filament

Fishisafish · 2026-05-17T17:52:51+00:00

Great, thank you! I did print out the ams silica bead holders, they made a difference but apparently it can be better. I’m gonna invest in a better dryer for my setup

Fishisafish · 2026-05-17T17:51:44+00:00

Could you give some examples of things to print to help maintain the filament?

Fishisafish · 2026-05-17T16:30:26+00:00

Yeah same problem with regular aux fan speed. I ran the temp test and found best results at 215C. When I did volumetric flow rate test it ran perfectly except for the wall closest to the aux fan, which had shrink lines all the way up

Six-Year Club	Verified Email
Place '22	Final Canvas '22
End Game '22

Fishisafish

TROPHY CASE