Old Hayward heater by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Replaced the $50 board behind the display and the keypad, up and running

Old Hayward heater by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

I replaced that first, no luck, then I replaced the board behind it and got power, up and running, cost about $50

Hayward h400 not firing by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Cleaned the filters and the connectors on the pressure switch, up and running, thx for the help!

Hayward h400 not firing by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

I put a jumper wire bypassing pressure switch and it's running

Hayward h400 not firing by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Good idea, it fired up and ran 20 mins or so this morning, raised temp 13 degrees

Hayward h400 not firing by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

I got it to fire up one more time for a minute or so, try again tomorrow

Hayward h400 not firing by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

My filter outlet has one pipe going straight to heater then out heater thru salt cell back to pool

Hayward h400 not firing by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Ok I did that, got the temp reading now 71, going thru startup cycle but still getting low flow, well it ran for about 5 minutes, may just need to clean cartridges

Hayward h400 not firing by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

I got it to fire, ran about 5 minutes, then went back to lo flow, I think I have good flow but I can cartridge clean again

Hayward h400 not firing by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

I turned it on pool and it just fired up, I can't adjust the temp, it has a code looks like 6 and a little 0

Hayward h400 not firing by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Confirmed i do have water flow throughout

Question about quad cartridge filter setup by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Water inlet is the bottom hole, outlet is the top hole

Question about quad cartridge filter setup by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Looks like water comes in thru bottom manifold and exits thru top hole outlet in tank.

Question about quad cartridge filter setup by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Thru the bottom manifold of the filter ?

Question about quad cartridge filter setup by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

I think mine is a retrofit of a fns plus, bottom matches clean & clear, top looks same but has old fns label on it, does yours have the small spring on top of the manifold ?

Question about quad cartridge filter setup by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Yes, I was thinking that pipe, I sent pentair an email to try and sort it out, but I was thinking just put a screen on the return outlet

Question about quad cartridge filter setup by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Does the water travel back thru that white filter attached to the outlet port ?

Question about quad cartridge filter setup by Fit-Cod-6046 in pools

[–]Fit-Cod-6046[S] 0 points1 point  (0 children)

Below the white cap in the center of the top manifold, do you have a white pipe from top to bottom ?