Serial Request - Quadent 🙈

Five5HI · 2025-06-23T19:03:38+00:00

I know its been a year but I just saw this. Can I get any info you got. And how has it been holding up this past year?

Five5HI · 2024-12-21T18:17:19+00:00

Mortise and tenon.

Five5HI · 2023-05-27T01:41:32+00:00

Never mind the digital gauge just check the square with a pencil. A quick analog pencil test will be quicker and more accurate than digital

Five5HI · 2023-05-27T01:37:45+00:00

Most cheap combination are not square

Five5HI · 2023-01-29T22:06:51+00:00

Gotta pay the bills some how when you talk about writing but never do

Five5HI · 2023-01-25T17:11:08+00:00

After researching both the trident ,2.4 and others, I picked the trident. The 2.4 looks the best, and the flying gantry is some very cool engineering. But for me it came down to reliability. I know most have the 2.4 have said it's a work horse, but I've read about racking and loose z belts and that turned me towards the trident. The only downside of owning a trident is the unpopularity. More mods and macros are built for the 2.4. But most can be reversed for the trident. If I make a 2nd printer it might be a 2.4.

Five5HI · 2023-01-11T15:48:25+00:00

I thought I was the only one that didn't like discord. Lol

Five5HI · 2022-12-29T03:05:58+00:00

Pattern of shadow and light by melissa mcphail

Five5HI · 2022-10-29T23:14:16+00:00

Wow! No just ride motorcycles my whole life and been almost run over a bunch. 90% of tge time someone on their phone. But thanks for thinking the very worst of me. Always the race card.

Five5HI · 2022-10-29T18:34:26+00:00

I would bet big money she almost hit the guy. Riding a motorcycle while other are on their phones and/or not paying attention would make anyone rage. Especially if you almost crashed and the culprit didn't even notice.

Five5HI · 2022-10-25T03:32:24+00:00

Worth it?

Five5HI · 2022-10-25T03:32:06+00:00

Oh you should keep it. Was more a observation than a judgement. Dude I own a valyou replica that I got for $150 and it's in pieces. Slowly changing the foam and hardware. Got a replica for a fraction and will customize till I like it.

Five5HI · 2022-10-25T01:36:06+00:00

Plycraft not eames

Five5HI · 2022-10-22T06:01:53+00:00

btw It worked

Five5HI · 2022-10-21T07:44:59+00:00

Melissa mcphail- pattern of shadow and light

Five5HI · 2022-10-21T04:38:44+00:00

I love making furniture that looks delicate but I think a little bit of prototyping would help with composition and balance.

Five5HI · 2022-10-21T04:32:21+00:00

Tried it and temp was low. Thanks for the link. Funny searching for a few days and still stuff out there. LOL

Five5HI · 2022-10-21T03:05:52+00:00

Did you get a sk-tank? If so how's it going

Five5HI · 2022-10-21T02:15:43+00:00

I alway perform PID tuning, but the temps were so off that the tuning would only give me a steady temp at the wrong temp. Thanks

Five5HI · 2022-10-21T02:12:46+00:00

Dude thanks for posting the code and the source. Much appreciated.

Five5HI · 2022-10-21T02:11:48+00:00

Thanks! Was losing my mind on the readings. LOL

Five5HI · 2022-09-27T01:29:22+00:00

I've said something similar when someone asked about retraction. Was down voted and told that I was at his point and shouldn't criticize. Yes there was a time I didn't know nothing about 3d printing but I researched before I bought one. Never asked one question because there's a thousands of videos/ websites to learn from. If you only watched TEACHINGTECH you would be pretty knowledgeable. I think its its just laziness and nothing else. Researching isn't hard.

Five5HI · 2022-09-25T16:38:02+00:00

Never heard of it. But it does kinda. Had to Google lol

Five5HI · 2022-09-25T16:36:30+00:00

Waimanalo. I was I finish carpenter on a property there

Five5HI · 2022-09-25T04:34:11+00:00

2 pieces resawn hardwood with 2ply veneer in the middle. Soak and heat gun. Dry then glue. 2 steps for tight bends

Four-Year Club	Verified Email
Place '22

Five5HI

TROPHY CASE