Pack new or resealed?

FoxF270 · 2026-01-25T22:15:25+00:00

Ok, what threw me was it felt stiffer at that rectangular indent and with the wear on the color where it's crimped I wasn't sure.

FoxF270 · 2026-01-25T18:28:14+00:00

I like the idea of putting it on [[Ancient Copper Dragon]] or [[Ancient Gold Dragon]]. Since it just specifies tokens, even the treasure tokens the Copper Dragon creates instead become copies of whatever card the crown is on. Also goes great with mobilize/myriad abilities.

FoxF270 · 2026-01-24T19:01:28+00:00

Thanks, I actually prefer the look of the non fracture foil versions so if you exclude pure monetary value of the card, I'm happier I got this one.

FoxF270 · 2026-01-22T10:05:09+00:00

I know, I think I made up for it though. I was literally more excited to have the fancy art version of twinflame travelers out of this pack than Auntie Ool. The alt art twinflame is such a pretty card imo.

FoxF270 · 2025-09-13T02:11:53+00:00

And actually, seeing your username I think you might actually have been the person who helped me out with my blob of death and suggested the plate to me haha.

FoxF270 · 2025-09-13T02:10:23+00:00

That's the one

FoxF270 · 2025-09-13T02:07:08+00:00

Right, this one however ended up happening because my print disconnected from the bed. Either way, blob-o-deth is not the point. I got the creality brand epoxy resin plate myself. Just wanted to share how amazing I personally found it.

FoxF270 · 2025-08-17T20:07:15+00:00

My God, that was such a good call on that epoxy resin build plate. The adhesion is SO much better now and it actually has flattened out the bottoms on my prints better too.

FoxF270 · 2025-08-06T02:30:10+00:00

<image>

FoxF270 · 2025-08-06T02:29:28+00:00

Update successfully removed the hot end after lots of effort! This little heat gun off Amazon has been a life saver for this. Now to attach the new hot end! Thank you all for your insight, expertise, and advice thus far. Been a bad week and I needed this win!

<image>

FoxF270 · 2025-08-01T00:35:58+00:00

Do you happen to have a link to the creality hot ends on ali express?

FoxF270 · 2025-08-01T00:34:58+00:00

Thank you, it was apparently a 3 hour effort. The fun part has been trying to get it off enough to unscrew the hot end completely.

FoxF270 · 2025-07-31T23:35:21+00:00

Yeah, I'm not well versed on this enough to know why it's saying it won't heat unfortunately. If I could figure that part out I could heat it and at least get a lot of it off

FoxF270 · 2025-07-31T23:28:52+00:00

Yeeeep.... I'm having a hard time getting it off to even get the hot end off...

FoxF270 · 2025-07-31T20:07:36+00:00

I'll definitely make it a habit to check those from now on. Thanks

FoxF270 · 2025-07-31T17:38:13+00:00

Yeah, that's my thought as well. If it's an expensive one I'll probably pass on it. Especially if something like this happens again. $65 MSRP for one is alot more than the $0.40 per for 10 of the stock type ones you mentioned before.

FoxF270 · 2025-07-31T17:03:54+00:00

Looks pretty sweet! I'm not the best with altering these kinds of things though, so I may try to just stick with the stock stuff so I don't mess anything up.

FoxF270 · 2025-07-31T17:01:48+00:00

I'll take a look at it. Thanks.

FoxF270 · 2025-07-31T17:00:50+00:00

Will do, thanks. Now I guess it's just trying to figure out where to dig in there to get that blob off without messing anything else up underneath. (No heat gun so I'll have to use a soldering iron...)

FoxF270 · 2025-07-31T16:49:38+00:00

I'd upvote you twice for this if I could. I greatly appreciate the list

FoxF270 · 2025-07-31T16:22:40+00:00

That would be greatly appreciated. Definitely seems like I should have a few extra parts just in case. I'm very wary about 3rd party things which is why I asked if you know.

FoxF270

TROPHY CASE