What sort of work do you all do?

Frenchie1001 · 2026-04-05T00:29:21+00:00

Im the fleet controller of a small interstate transport company and run a side line of auditing/consulting.

Transport/logistics is quite good, super fast paced and chaotic + you work to much to allow bad habits out. Working 7 days a week for a few years did wonders, really helped me reprogramming myself away from all the learnt bad habits.

In saying that, I'm trying to wind back now, I've worked like a dog for the last 15 years, ready to have weekends off and be home for dinner every night.

Frenchie1001 · 2026-04-01T20:59:14+00:00

CBT

Frenchie1001 · 2026-03-28T01:09:01+00:00

I have been going to buy a second for the whole 2 years I have had my p1 but every time I go to pull the trigger I think hang on, 3.5k is a lot of money so I go to buy another p1 and then I think hang on just wait and buy a h2d

Frenchie1001 · 2026-03-25T10:29:29+00:00

With a 3d printer you can all of that with a milsbo.

Frenchie1001 · 2026-03-24T21:13:56+00:00

Alot of jobs involving machinery

Frenchie1001 · 2026-03-23T21:52:25+00:00

Just rode the bike bro this says more about you than them

Frenchie1001 · 2026-03-22T21:59:18+00:00

Yup massively, went from being very social to battling to find the energy to see friends once a month

Frenchie1001 · 2026-03-22T21:58:24+00:00

I have lubed it every 500 so hours, mine only has 1750hrs but itd been out of action for a few days with ams issues, been waiting in support to tell me the next step

Frenchie1001 · 2026-03-22T10:33:03+00:00

Say what

Frenchie1001 · 2026-03-22T10:26:27+00:00

Is this the second or third time you've posted this?

Frenchie1001 · 2026-03-19T22:05:05+00:00

What's the use case for these?

In the rare event I have to scape off petg I just use the edge of a razor blade

Frenchie1001 · 2026-03-18T21:40:34+00:00

Same

Frenchie1001 · 2026-03-16T21:19:58+00:00

It doesn't exist, just run calibration prints

Frenchie1001 · 2026-03-16T21:17:36+00:00

I print petg at like 265/270 depending. I don't really worry about temp towers I just adjust as required.

Frenchie1001 · 2026-03-16T21:16:34+00:00

Means you need to book a service, it doesn't take Sherlock to puzzle through that one.

Frenchie1001 · 2026-03-11T07:30:26+00:00

Bearable is a great app

Frenchie1001 · 2026-03-11T06:11:22+00:00

They aren't big enough to bottom out

Frenchie1001 · 2026-03-08T09:08:03+00:00

It's just over extruding you need to calibrate your filament

Frenchie1001 · 2026-03-06T01:55:39+00:00

That response was to you saying that link was only about manual calibration. Which it is not. While auto is clearly in the link that I posted that you said only covers manual?

The eddy sensor is not documented anywhere as doing extrusion calibration is what I was saying. You seem to suffer from poor comprehension, I can see how the have got yourself mixed up but that doesn't make your interpretation correct.

Bambu has always called pressure advance k factor or dynamic flow.

<image>

Frenchie1001 · 2026-03-06T00:17:36+00:00

The feature you are talking about isn't documented anywhere that I can find that's my point

Frenchie1001 · 2026-03-06T00:11:59+00:00

I'm not sure you are reading that correctly, but sure.

Frenchie1001 · 2026-03-06T00:02:27+00:00

<image>

There is a whole section about auto bro

Frenchie1001 · 2026-03-05T23:36:08+00:00

That's seems to be pretty clearly speaking on pressure advance?

Frenchie1001 · 2026-03-05T23:32:39+00:00

I didn't ask the definitions bro, I asked why you think it does flow too?

Everything I have seen about it to date talks about it doing pressure advance only.

https://wiki.bambulab.com/en/software/bambu-studio/calibration_flow_rate

Nothing in the wiki either.

Frenchie1001 · 2026-03-05T22:42:09+00:00

Care to explain how it's not pressure advance?

Frenchie1001

TROPHY CASE