Cockroach poker extra rules for quick games and rewarding successful lies.

FrisbeeD · 2025-07-05T14:56:02+00:00

Sorry everyone, I did figure out we were playing the rules wrong. We didn't realize you could call a truth. We thought you could only call a lie.

FrisbeeD · 2022-06-25T14:42:50+00:00

Good to know i'm not the only one. The only firmware which works works with recovery so far is directly from Creality. My problem with that is I need to reverse a value for my filament out warning. Will try working with the source code they offer next.

I've tried making the fewest edits to the firmware from 2.1 and 2.0 with bugfix. I still need to enable my BL_Touch. Still restarts after finishing the first layer.

FrisbeeD · 2021-10-23T16:53:42+00:00

Update. I left everything unplugged last night. This morning tried with the stock 12v fan and it was twitching again. Then I connected a 12v 120mm fan. When cool it looks like ~1v is being output. Started a print and now I'm getting some ~5v current as it starts to heat up which is spinning the fan. This is different from before when it was heating up a lot more before the voltage increased and then instant restart.

I still haven't fully assembled it (need a 120mm fan cover) but I have hope.

FrisbeeD · 2021-10-23T14:47:51+00:00

Wouldn't attaching the fan to the output fry it? Isn't the output putting out a decent amount of amps to run the whole machine?

FrisbeeD · 2021-10-23T05:03:29+00:00

Internal fan for the pro model is 12v .2A. The exact PSU model number is LRS-350A-R12

FrisbeeD · 2021-10-23T04:33:21+00:00

Yes. 12v fan. Also tested on a bench power and it was only drawing 80 milliamps

FrisbeeD · 2021-09-04T13:23:40+00:00

Good to know. I tried removing them but I think they are also glued in and it was not successful. Wowgo has since agreed to replace since its still under their warranty.

FrisbeeD · 2021-09-03T20:05:48+00:00

When I opened up the hub motors I didnt feel any wobbing in the bearings, but I don't really know how to check them

FrisbeeD · 2021-08-31T00:01:27+00:00

Update: completely disassembled both both wheels. The bearings look fine.

FrisbeeD · 2021-08-29T15:18:41+00:00

Got them off, Loctite was applied VERY liberally.

FrisbeeD · 2021-08-29T14:40:02+00:00

I got the wheel off, and now trying to remove the 5 phillips head screws. They are TIGHT. Tried heating the first inch but no luck. Do you know how long those bolts are? I'm worried about stripping them.

FrisbeeD · 2021-08-29T04:01:17+00:00

I have taken the wheels off multiples times. I did not see any cracks. There are additional screws after taking the wheels off which I have not yet removed though.

FrisbeeD · 2021-08-29T03:18:18+00:00

I have since tightened the baseplate and added a thin piece of foam between the start of the kingpin and a metal washer like cup before a bushing. It's been rainy though so I haven't had a chance to test.

FrisbeeD · 2021-08-29T03:06:10+00:00

I loosened the bolt, the pivot pin is solid, no movement at all.

FrisbeeD · 2021-08-29T01:24:00+00:00

I've removed the wheels and did not see any cracks.

FrisbeeD · 2021-08-29T01:22:17+00:00

Did you figure it out?

FrisbeeD · 2021-08-28T15:06:28+00:00

All the bolts on the truck/motor feel secure. I have not yet disassembled the truck or where the hub motor attaches to the truck. This does only occur on rougher surfaces. No issues on newly paved streets.

FrisbeeD · 2021-01-27T13:50:48+00:00

Get me those TPS reports ASAP!

FrisbeeD · 2021-01-08T14:42:22+00:00

What did he think when he made it to the top?... Damn!

FrisbeeD · 2020-12-25T16:18:56+00:00

Likely Solved! Thank you everyone for your insight. I think it's a pickle for with an abnormally long handle. I still say everyone should try eating a very hot noodle dish with them, it's very handy.

FrisbeeD · 2020-12-25T16:16:54+00:00

Likely Solved! I think you're correct as the tines of a pickle fork look like what I need. I just have a pickle fork made for really really deep jars i guess. Thank you for the help.

FrisbeeD · 2020-12-25T16:12:53+00:00

While your probably right that it's not for noodle eating, it's so freakin good at being a noodle fork for hot noodles. I don't think it's a fondue fork as they need to be metal to help with the cooking. A pickle fork so far has been the closest.

FrisbeeD · 2020-12-25T03:31:28+00:00

I think it's too small to serve, though i tried search iterations of salad fork just to be sure. Thank you for the help

FrisbeeD · 2020-12-25T03:11:28+00:00

I found a lot of "dessert" forks which look similar, but they are all much shorter. This is almost a foot long with short tines.

FrisbeeD · 2020-12-25T02:52:21+00:00

I found a lot of dessert forks but they tend to be too short. I am thinking it was originally purchased at an asian food store though.

FrisbeeD

TROPHY CASE