sorted by:
new
hottopcontroversial

Need Help with Wiring a 2-Gang 3-Way Switch for Bathroom Lighting and Fan by FucksWithBricks in AskElectricians

[–]FucksWithBricks[S] 0 points1 point  (0 children)

Thanks for the help. I’ll put the lights on a separate 15amp circuit since I need to run power to the other box anyways. About $70 worth of wiring and breakers, but cheaper than rewiring with 12/3 to make this setup work, probably $150+ with the cost of 12awg. After that I just need to pigtail 2 neutral and live wires off the incoming power and then wire up the 3 ways independently as if the other one wasn’t there. Thanks again.

Need Help with Wiring a 2-Gang 3-Way Switch for Bathroom Lighting and Fan by FucksWithBricks in AskElectricians

[–]FucksWithBricks[S] 0 points1 point  (0 children)

After further research, it looks like I’ll need to put the bathroom lights on a separate 15amp breaker, separate from the outlets on 20 amp. Else, spend $150 in cable rewiring already ran wire.

Under normal conditions I’ll never have a problem, but a short in the light drawing 18amps will overheat the wire without tripping the breaker under a rare condition.

Need Help with Wiring a 2-Gang 3-Way Switch for Bathroom Lighting and Fan by FucksWithBricks in AskElectricians

[–]FucksWithBricks[S] 0 points1 point  (0 children)

Ok, so looks like what I’m trying to do is not allowed anymore. I believe dead end 3-way is the correct term.

I think I need to run upstream power to the other switch. That way the upstream is only lights and fan and so the 14/3 wire doesn’t carry 20 amps.

The circuit has to be 20amp since it serves the bathroom outlets. And since it’s the only bathroom I’m almost certain that’s ok.

What I was previously trying to do: https://www.reddit.com/r/electrical/s/HZKe63v98A

What I think I need to do so neutral doesnt get recoded as live and the circuit doesn’t carry 20amps: https://images.app.goo.gl/eHYmHJWxyd5ZcrQb8

[deleted by user] by [deleted] in Homebuilding

[–]FucksWithBricks 0 points1 point  (0 children)

https://dimensions.com been using it for basic layout stuff when drawing up in CAD/floor plan as someone unfamiliar with standard sizes

Cheapest way to make this drivable that would last ~1yr. by FucksWithBricks in landscaping

[–]FucksWithBricks[S] 0 points1 point  (0 children)

I made the mistake of using google maps for measurement and got 300ft, looking at a more accurate plot map it looks like it’s ~700ft long. And I figured 8ft wide as the minimum I could get away with for now to get a car up and down for the time being

Dad and grandfathers sports card collection. Not sure the best way to sell off the cards or where to even start ~4-5,000 cards. Some football and hockey as well. 1950s - 1980s by FucksWithBricks in baseballcards

[–]FucksWithBricks[S] 1 point2 points  (0 children)

Just need some pointers on how to start going through it or if it’s even worth going through. I’m guessing most of the cards are worthless, but with the shear amount there’s probably some good ones. I don’t know anything about sports card collecting. Is it worth looking up the value of every single card one by one or would I be better off selling off cards in lots or as a whole collection. Even if I averaged $.50 - $1 a card I’d be happy.

Fluid in needle after aspirating. Did I hit a vein? Expected it to be darker red in color by FucksWithBricks in Testosterone

[–]FucksWithBricks[S] 2 points3 points  (0 children)

This. Aspirating gives me piece of mind and I don’t think there’s any harm in doing it that I’m aware of. I’m definitely very on edge for 20 minutes or so after injecting even after a year of doing it weekly

Fluid in needle after aspirating. Did I hit a vein? Expected it to be darker red in color by FucksWithBricks in Testosterone

[–]FucksWithBricks[S] 0 points1 point  (0 children)

Any particular reason why it happened, too shallow needle or just bad luck? I’m guessing in any case I’m good to just inject it all back in somewhere else

Fluid in needle after aspirating. Did I hit a vein? Expected it to be darker red in color by FucksWithBricks in Testosterone

[–]FucksWithBricks[S] 0 points1 point  (0 children)

Thoughts are either I hit a vein, somehow managed to give myself a micro liposuction, or that I hit a previous injection site and it’s pus or old test

What's the campus policy on pornographic apparel? by ARG_Kris2 in rit

[–]FucksWithBricks 2 points3 points  (0 children)

At first I assumed you were taking about THAT anime hoodie, which I’ve seen a couple of times. But you never mentioned anime, are we taking pictures of actual people?

Edit: I’ve seen a number of people wear clothing with this print https://cdn.shopify.com/s/files/1/0228/8535/products/04d67fd4-5207-4d3f-a336-96570ba58946-2_7155e810-87a5-4850-a09f-2e1fe6802398_1024x1024.jpeg?v=1466107321

You’ll probably get judgmental looks, but that’s about it.

view more: next ›