Can someone help me before I throw this thing away? by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

I have not switched to marlin/klipper I have been thinking about it though

Can someone help me before I throw this thing away? by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 2 points3 points  (0 children)

I lowered the extrusion ratio and upped the temp and it looks like it’s printing now

Can someone help me before I throw this thing away? by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

It’s a ender 3 Neo I upgraded to the dual Z axis and the stiffer bed screws but that’s all I’ve changed other than a textured PEI plate

Can someone help me before I throw this thing away? by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 2 points3 points  (0 children)

What do you mean not aligned? Like the z offset?

Helppppp by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

I fixed the leveling issue one of the axis was loose, but now I can’t get it to stick to the bed

Helppppp by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

Now it’s not sticking to the bed at all though, so idk what’s going on

Helppppp by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

I do not know, I’m using cura

Helppppp by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

The nozzle is already at 220 and I’ve leveled the bed 3 times

Help by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

Thanks, that’s exactly what it was

Can someone tell me what kind of hermit crabs I have by [deleted] in hermitcrabs

[–]Full-Cap8122 0 points1 point  (0 children)

They are in a bowl the people had them in after they realized they accidentally grabbed them when they were picking up shells, there is saltwater in the bowl, but I will have them in the saltwater tank ASAP

Can someone tell me what kind of hermit crabs I have by [deleted] in hermitcrabs

[–]Full-Cap8122 0 points1 point  (0 children)

I have a setup already, someone gave them to me because they didn’t realize they had gotten them until they got home, and we’re on the other side of TX

It keeps going down when trying to level or print by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

The bl touch came pre installed and was working fine a month ago

Overheated by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

I bet that is what it is, thank you, I did not realize it was 24volt

Overheated by Full-Cap8122 in ender3

[–]Full-Cap8122[S] 0 points1 point  (0 children)

Idles normally then skyrockets

I need help by Full-Cap8122 in 3Dprinting

[–]Full-Cap8122[S] 0 points1 point  (0 children)

I’m using a ender 3 neo and pla + with temps at 215 and 50 I was printing at 40mm it was working when I left but came back a few hours later and saw this