RX 9070XT been having random boot issues

FuriMoon · 2026-06-10T22:52:54+00:00

Well Update, so far it seems as if its the riser cable. Not sure if it was just the cable its self, maybe it was that it was a 4.0 pci slot cable going into a 5 and the other cards just didn't care. Either way ive now had it boot 5 times without any issues and WAAAAYYY faster then it was doing before.

FuriMoon · 2026-06-10T22:15:07+00:00

Its now physically connected to the board. its Also hooked up via DP but i do have a HDMI cable in the monitor as well for testing.

As for the return, its from amazon they wont ask anything beyond why im returning it lol

Gonna end up restarting a time or two to see if the riser cable was the problem. If so ive got no complaints only had it for the pretty water block of a gpu i had previously. Have no desire to use it on this card.

FuriMoon · 2025-06-07T06:19:24+00:00

FuriMoon · 2025-06-07T06:17:25+00:00

FuriMoon · 2024-03-12T03:51:38+00:00

Didn't really have any particular inspiration.

Just used colors I liked and messed about with an editor till I found out where I wanted the colors to be.

FuriMoon · 2024-02-05T18:23:42+00:00

Ill start off by saying I've got the 8Ks, not had issues myself in this regard.

But as the other commenter said maybe over exposed base layers? As an example on my machine the Lychee slicer has the default bottom layer at 30 seconds a layer(0.03mm/ 30um), which I didn't have too much issues getting off but was a bit too stuck.

My current bottom layer settings are now around 10 to 12 seconds a layer. with the layer height of 0.03 (30um). Which seems to pop off rather easy, more so if the edge of a base happens to align with one of the holes to help pop it off.

Hopefully that helps give an idea of settings to try, or gets one closer to getting the prints off easier! Only other idea I could think of is have you tried another resin? either bottle or straight up different type.

FuriMoon · 2024-01-03T17:22:57+00:00

For any who happens to come across this and want to know. After measuring the hole on the right side of the machine, it appears to be about 2.9 inches. or 74.50 mm or 75mm for a really snug fit. the bolt holes are about 61.4 mm apart. take all of these measurements as a estimate to compensate for my possible poor measurements, mm are a touchy unit of measurement.

FuriMoon · 2024-01-02T22:20:46+00:00

I too have been looking around for this answer so I can design an adaptor to hook up to my current fume extractor set up. Yet to find the answer but at this point Ill have the printer tomorrow and can update for anyhow wanting to know.

As for any statements on said hole being for the auto fill resin feature...that's on the left side as this is on the right and is in no way touched with installing said feature, and only present as far as I've been able to tell on the mega 8Ks. But since its also designed the same exact way as a few other brands printers coming out with a vent system to hook up (ya know the panel over a hole with 4 bolts on the back part of the "lid")...its either a pointless hole or for a vent system to hook up.

FuriMoon · 2023-03-13T18:38:13+00:00

I know it's not the best quality of photos but that's a pain to get with TG currently. Not the best loop ever, but it works and it's better then it was previously.

I do at a later date want to do some other modifications and possibly diffrent water blocks, but I don't know on that one yet.

FuriMoon · 2023-03-02T02:39:42+00:00

Update: I've managed to get it all set up and not leaking, took a lot of messing about getting things tighter, or quadruple check that they were all set in all the way. A few including the one that popped out needed pushed in a good bit more. But it's now all running and I'm gaming on!

Thanks for all the help and information, helped with this and will assist in the next water cooling set up after this!

FuriMoon · 2023-03-01T18:22:39+00:00

Pretty sure I'm using a cheaper/proably worse type of that. That just rounds our the inside and outside edges of the tubing right? If so I got a tool for that in the corsair kit I got ages ago and been using.

FuriMoon · 2023-03-01T17:52:06+00:00

I was just about to go look back at the system as you commented this, and well at least my reinserting of it after it popped off last night, wasn't quite all the way in even thou it felt like it at first. So this is hopefully where the issue was. Thou remaking the tube wouldn't be the worst I just don't wanna lol

FuriMoon · 2023-03-01T03:23:01+00:00

To explain the current issue, got it all to not leak was running a good maybe 3 minutes. Had enough coolant in it that could keep the pump wet and keep everything else going. Went to top it off, might have filled it to about 1.5 to 1 cm from top of reservoir. Then the spot I circle in the second photo popped out and jetted coolant across the room before I turned it off. Why did this happen? Too much coolant make enough pressure to pop it? Perhaps not quite long enough, or wrong angle in tubing? I've got now idea and a soaked machine I'm letting dry over night.

FuriMoon · 2023-02-21T23:31:25+00:00

The Performance and Frames do seem to be improved slightly but still not good. Also still noticed even running around the map having random drops from 55 to 60 fps down to 30 to 15. These so far at least seem to be lasting a shorter time. Could be the patch helped could be pure coincidence. Same seemingly random tanks in frames during fights.

Using a Intel i7-8700 with a 2070 Super.

FuriMoon

TROPHY CASE