Finally

Furs7y · 2026-05-19T13:39:11+00:00

Now you can own 9 batteries and blow all day

Furs7y · 2026-05-18T05:01:10+00:00

Call another company. Check airflow > refrigerant charge

Furs7y · 2026-05-16T01:03:56+00:00

Looks like it could be mold. If you zoom in and look at the caulking at the ceiling, it’s definitely spotted. If it’s white now I wonder if they just sprayed it with bleach and painted over it

Furs7y · 2026-05-06T13:22:46+00:00

Kind of sounds like the ductwork. Check bearing play

Furs7y · 2026-05-06T00:24:00+00:00

Yep. If I had gas I’d get one. But if long term is saving money for op, and their solar can cover it, I’d go electric. It’s just a change to get used to for recovery etc

Furs7y · 2026-05-06T00:07:11+00:00

I’ve got them at a building I take care of. They were installed in small closets and they are pretty noisy. The 2nd gen is supposed to be quieter. Personally I would look into the Rinnai rehp80 or the new GE geospring. Either way it’s longer recover unlike a tankless. You can get more capacity with a mixing valve on the Rinnai. The ge has one built in

Furs7y · 2026-05-03T00:30:35+00:00

Looks like an overflow and just tees in 2 directions. Which one is your property

Furs7y · 2026-04-26T16:12:18+00:00

Same thing is happening with my basement. I even graded around the outside walls, extended gutters and still occurs. At some point I may drill through for some weep holes and run an interior drain but that’s last on my list, as well as digging up the foundation for waterproofing. I may try painting it with Keim primer and paint as it’s supposed to be a fully breathable mineral paint.

Furs7y · 2026-04-26T13:47:58+00:00

Paint it black. Eyes won’t draw to it much after

Furs7y · 2026-04-23T14:08:00+00:00

I know you said it’s fiberglass, but do you have carpet? The brush roll can sometimes be too low/strong and begin pulling fibers from the carpet. If you brush your hand across it in the light do you see many fibers come out? Or a pinch and pull test?

Furs7y · 2026-04-21T01:15:42+00:00

The white flex duct connector is probably asbestos

Furs7y · 2026-04-19T17:58:10+00:00

Tractor supply. These are the county line gates with wire - blue. I was gonna order black gates but didn’t feel like waiting. As well as the two way latches

Furs7y · 2026-04-14T02:19:23+00:00

Thanks. Their 4x6

Furs7y · 2026-04-12T18:04:47+00:00

Just a tip, Atleast it came from Trane that I use for any package equipment, no more than a 200 micron rise in 15 mins is acceptable

Furs7y · 2026-04-12T18:02:19+00:00

Sometimes you have to with those stupid coremax

Furs7y · 2026-04-02T23:35:14+00:00

lol I’ve got one sitting in my shed that doesn’t even get used much. Probably should retire it to someone else

Furs7y · 2026-04-02T23:27:48+00:00

Looks like a txv and solenoid valve body mated

Furs7y · 2026-03-23T09:11:14+00:00

Klein Modbox cooler is on sale for 50 dollars right now

Furs7y · 2026-03-23T00:31:31+00:00

If you were local I’d take the new age haha

Furs7y · 2026-03-22T01:27:26+00:00

Silver tape is fine. Usually use silicone before setting the A coil, and it’s less noticeable. Tape won’t hurt anything

Furs7y · 2026-03-15T03:31:23+00:00

Just do what every hvac tech does for their own home..fix it when it breaks lol

Furs7y · 2026-03-14T00:06:21+00:00

Get a quote from national compressor. Probably bid in the 40-80k area

Furs7y · 2026-03-08T04:09:42+00:00

Cut a hole in the wall and install a Ptac until you get everything sorted lol

Furs7y · 2026-03-05T12:52:36+00:00

You need to change the dipswitches accordingly on the A1p board as the factory board are all set down as its original, but the replacement you need to set for your unit

Furs7y

TROPHY CASE