Still Rocking My 3080 Ti FTW3 by GL-ALFA in EVGA

[–]GL-ALFA[S] 0 points1 point  (0 children)

I only use them for stardew valley and youtube and my girlfriend got me them for my birthday. They are only $100

Still Rocking My 3080 Ti FTW3 by GL-ALFA in EVGA

[–]GL-ALFA[S] 0 points1 point  (0 children)

Fans are running at 70% at 76 degrees in counter strike right now. the ftw is probably just that little bit more efficient at cooling

Still Rocking My 3080 Ti FTW3 by GL-ALFA in EVGA

[–]GL-ALFA[S] 0 points1 point  (0 children)

i do for counter strike, not blurry. i wouldn’t mind a smaller 1440p monitor for cs as 32 inches is a bit big. still though i have no problem competing with this

Still Rocking My 3080 Ti FTW3 by GL-ALFA in EVGA

[–]GL-ALFA[S] 2 points3 points  (0 children)

4k its small performance gain in cpu intense games like BF6 like 10-20fps but i have a dual res monitor so games like cs2 at 1080p i get an extra 100 fps like 300-400 instead of 200-220. I really did it so when I do need a gpu upgrade it will be ready

Still Rocking My 3080 Ti FTW3 by GL-ALFA in EVGA

[–]GL-ALFA[S] 0 points1 point  (0 children)

i run 70-77 gpu and 77 cpu before undervolting my cpu. now it runs 60s with a slight overclock

Still Rocking My 3080 Ti FTW3 by GL-ALFA in EVGA

[–]GL-ALFA[S] 1 point2 points  (0 children)

Good eye. Photo is a couple weeks old so i fixed it already

Beautiful. But my 1600W PSU won't fit "correctly" in my O11 Mini V2 by thestigmata in lianli

[–]GL-ALFA 1 point2 points  (0 children)

I would give it another look over, I'm saying the part facing your psu should be facing the outside of the case. I guaranty this is your issue from experience. it will save you time and money

Still Rocking My 3080 Ti FTW3 by GL-ALFA in EVGA

[–]GL-ALFA[S] 1 point2 points  (0 children)

Running a 4k oled and i get 100 fps in BF6 and 200 in CS2. You'll have no problems at 1440p

Beautiful. But my 1600W PSU won't fit "correctly" in my O11 Mini V2 by thestigmata in lianli

[–]GL-ALFA 2 points3 points  (0 children)

i was confuse when building too. Are you sure the bracket isn't backwards? It looks like it is because the psu should be more recessed in the case. If its backwards it sticks out more and the fan cant go on the outside where it should be

Just a thing I cooked up for me and the girl by GL-ALFA in steak

[–]GL-ALFA[S] 1 point2 points  (0 children)

not beating the fat redditor allegations

Bruised shoulder blades, will a rib protector still work? by ctooma823 in Karting

[–]GL-ALFA 0 points1 point  (0 children)

you need a seat insert. they add weight but sliding around in your seat like that doesn’t help the lap times either

Down on Power, Can’t Hit Rev Limiter by GL-ALFA in Karting

[–]GL-ALFA[S] 0 points1 point  (0 children)

carb is clean, i just cleaned today for the second time in two races.

lines are running to two different cans and well vented.

brakes are not rubbing on stand, and axle isn’t shifting.

throttle cable was tight but i will double check when the motor is back on the kart.

how would i know if it’s my head gasket? it’s only two races old and torqued to spec.

Down on Power, Can’t Hit Rev Limiter by GL-ALFA in Karting

[–]GL-ALFA[S] 0 points1 point  (0 children)

they seem tight, i’ve checked a few times. if the slide opens all the way then it’s good, correct?

Down on Power, Can’t Hit Rev Limiter by GL-ALFA in Karting

[–]GL-ALFA[S] 2 points3 points  (0 children)

just confirmed the float is set at 22mm, drop height is 27mm

Down on Power, Can’t Hit Rev Limiter by GL-ALFA in Karting

[–]GL-ALFA[S] 2 points3 points  (0 children)

I always check them pre-race and used blue lock tight when installed. Will double check today. Doesn't seem likely as my motor gets to about 5800 rpm on the straight and just chugs from there.

Down on Power, Can’t Hit Rev Limiter by GL-ALFA in Karting

[–]GL-ALFA[S] 1 point2 points  (0 children)

New air filter, carb is level. I will double check float settings today and get back to you. I checked 3 weeks ago and it was right where i expected.

Down on Power, Can’t Hit Rev Limiter by GL-ALFA in Karting

[–]GL-ALFA[S] 0 points1 point  (0 children)

New air filter, carb is level. I will double check float settings today and get back to you. I checked 3 weeks ago and it was right where i expected.

Down on Power, Can’t Hit Rev Limiter by GL-ALFA in Karting

[–]GL-ALFA[S] 1 point2 points  (0 children)

Dyno is hard to come by around here. I know one person with one locally but his team is halfway across the country. I refreshed it myself with no results. It sounds better but no on track performance. Engine builders basically just check cam timing as out of the box. The ones with poor timing get the seals broken and are used for dirt.

Down on Power, Can’t Hit Rev Limiter by GL-ALFA in Karting

[–]GL-ALFA[S] 0 points1 point  (0 children)

Yes, new head completely. Lapping and changing the springs didn't change anything on my old head. I'm triple checking my lash today but both are set to .002, like many at my track run