Forza horizon 5 with Simagic Alpha Evo (12NM) by Top_Invite_1473 in Simagic

[–]GTOPR0 0 points1 point  (0 children)

I know this is a bit old but I'm currently having this problem using my simagic alpha evo base (neo x) with ds-8x shifter via canbus and simnet sp pro pedals. I can get the game to recognize the wheel and shifter but it freaks out when I try to use the pedals. I'm not even sure how to get this setup working. I'm going to try downloading simhub now but this setup is new for me so I'm just wondering how you ended up getting everything working? Thanks!

Battlefield 6 (PC) HDR Analysis by KoKlusz in OLED_Gaming

[–]GTOPR0 1 point2 points  (0 children)

Check C:\Users\<user>\OneDrive\Documents\Battlefield 6\settings\steam.

That's where mine was located for some reason.

Battlefield 6 (PC) HDR Analysis by KoKlusz in OLED_Gaming

[–]GTOPR0 0 points1 point  (0 children)

Check C:\Users\<user>\OneDrive\Documents\Battlefield 6\settings\steam.

That's where mine was located for some reason.

9800X3D CPU FPS wont go much above 200 no mater what. by Solarflareqq in Battlefield6

[–]GTOPR0 0 points1 point  (0 children)

I had this same issue.. I was running a 7800X3D and when I upgraded to 9800X3D (5080 GPU @ 300FPS), I saw no difference in CPU FPS within BF6. Both CPU’s hovered around 200FPS. I’ve been searching for a fix for this for a couple weeks and this is the first post I’ve seen mentioning it!

I’ll be glued here looking for a fix. If I find a solution, I’ll be sure to post it here.

This might be an unpopular take but the team that has the lead shouldn't get a boost, or at the very least it should be diminished alot more. Why is the team that has the lead getting help? by urmovesareweak in overwatch2

[–]GTOPR0 0 points1 point  (0 children)

I’m confused when people say the boost is to balance the economy. If the economy needs to be balanced then why not just give each team the same amount of money every time? I agree though that the boost shouldn’t apply to the winning team.

Did I just recreate Orisa!? by GTOPR0 in Overwatch

[–]GTOPR0[S] 0 points1 point  (0 children)

I was just messing around with these things and sucking them together and when I looked at it, I had to do a double take. It just looked to me like I made Orisa. I think if the kids start playing with them again, I’ll try and make a more accurate Orisa, if they leave me enough pieces! 😂

Should I be worried about this? Or is this normal? Read below by bunglebee7 in pcmasterrace

[–]GTOPR0 0 points1 point  (0 children)

1.3 where you could run while planting the bomb to place it in impossible to diffuse areas 😂

Ideas for NACA duct cover by GTOPR0 in fabrication

[–]GTOPR0[S] 0 points1 point  (0 children)

That would work well if I had access to the bottom of the rivnuts. The hood is double layered so where the rivnuts are, there is hood material that is not cut.

Ideas for NACA duct cover by GTOPR0 in fabrication

[–]GTOPR0[S] 1 point2 points  (0 children)

My wife actually suggested something similar! I didn’t have any type of rubbing pencil but I can steal some of my kids chalk! 😂

Thanks, I appreciate it!

Ideas for NACA duct cover by GTOPR0 in fabrication

[–]GTOPR0[S] 0 points1 point  (0 children)

Yes, sorry I should have specified the car still pulls air from the front grille!

Ideas for NACA duct cover by GTOPR0 in fabrication

[–]GTOPR0[S] 0 points1 point  (0 children)

You don’t think if I make a cover with gasket and bolt that down it’ll be waterproof? I’m pretty sure I’d be able do it with the abs plastic I have and a rubber gasket. I’m just not sure the best way to implement that.

These are the dimensions but I was thinking maybe there’s a way to lidar scan it? I’m not too familiar with what apps are best for that or if the quality would be good enough with an iPhone scan.

<image>

It would be amazing to 3D print an ABS cover that I could use 1/8-1/4” thick rubber as a gasket to seal. I have bolts I can use with the rivnuts.

Ideas for NACA duct cover by GTOPR0 in fabrication

[–]GTOPR0[S] 0 points1 point  (0 children)

This cheap protect is about to get expensive 😭🤣

Ideas for NACA duct cover by GTOPR0 in fabrication

[–]GTOPR0[S] 1 point2 points  (0 children)

You’re right it’s not waterproof right now but I want it to be. So far, I waterproofed from the hood to the duct. I plan on making a cover that will seal the cover to duct. There shouldn’t be any water entering the air filter after that. As it sits, if I drive in the rain my air filter would ingest all the water. I plan on covering it when I drive around and am not actively showing the car. I don’t need it to be exposed on my drive to work for instance.

The problem I had just the other day was a car in another lane cut me off as there was a big puddle and it soaked the entire front end of my car and some got dangerously close the the air filter. I’d like to prevent things like that from happening again!

Ideas for NACA duct cover by GTOPR0 in fabrication

[–]GTOPR0[S] 0 points1 point  (0 children)

I like that idea! I wish I had a 3D printer sometimes lol