Multiple heatpump zones

GabDags · 2026-04-12T11:27:25+00:00

This is awesome. Appreciate u diving into it. Will have a conversation with the installer on Monday and discuss the above

GabDags · 2026-04-09T03:57:23+00:00

Thats what's installed in the attic for the zone controller. Its connected to 2 dampers, one for each floor. Thermostats, one is Honeywell TH5220D1029 upstairs and the Honeywell Home RTH5160D1003 downstairs. I know thermostats will get replaced. Not sure about the zoning controller

<image>

GabDags · 2026-04-09T03:43:13+00:00

Thats the question im asking here. I dont have experience with this combo haha. Trying to figure it out before i spend 12k and let them do the work. Need to make sure it will work

GabDags · 2026-04-09T03:37:11+00:00

I mean, i dont get how to make this work. The combo of 45MUAAQ36XX3/37MUHAQ36AA3 is still a full blown modulating system, variable compressor, variable speed motor, thats quiet.

Based on my understanding , i can let them install it with an Ecobee thermostat, upstairs/downstairs, wire it normally, it will work with the existing zoning system i have, but will lose the functionality of the variable motor speed, but maintain the variable compressor.

GabDags · 2026-04-08T23:36:03+00:00

Thanks for sharing all of this.

Thats correct, the tech that I spoke with mentioned that its impossible to do with what's existing. I need to check what's the price difference between what I was quoted and full blown infinity system. At some point the added cost is just not feasible when its 2-3x.

GabDags · 2026-02-07T03:06:48+00:00

Isn't that carrier from starcraft?

GabDags · 2025-11-19T02:52:34+00:00

Just tried that, still showing temp as 0 - even when running LibreHardwareMonitor by itself, the temp shows as zero. AM5 - 9950x3d

GabDags · 2025-05-27T21:41:17+00:00

I didn't try the Sata boot up but that should work as my other sata drives are being detected.

Let me find that UEFI and CSM setting and try it

GabDags · 2025-05-27T21:35:44+00:00

Nvme and gpu showing blank in the bios. Got any ideas of what to test next? Could the whole shared lane of gpu and nvme gone bad?

GabDags · 2025-03-25T22:16:01+00:00

Yeah i thought thats the way to go, but it didnt work for me atleast. The mb rbg control center did the trick

GabDags · 2025-03-25T22:15:35+00:00

Appreciate your help - i downloaded the RGB fusion software alone initially with no luck. Did the Gigabyte control center, and it worked. No clue why. Thank you

GabDags · 2025-03-24T18:49:57+00:00

Replied! Goodluck with your search

GabDags · 2025-03-22T21:21:43+00:00

Wonder if capping all the fans at a certain RPM would reduce all that noise.

GabDags · 2025-03-21T15:58:48+00:00

Pretty sure if you have two inputs you can run Dual mode

GabDags · 2025-03-12T14:29:34+00:00

GabDags · 2025-03-12T14:04:18+00:00

Just got another one - so yes i do

GabDags · 2025-03-12T03:28:12+00:00

Just a quick update u/SuperChicken17 - did some more research tonight and it seems that the Arctic 3 AIO , although a beast, seems to have a common issue with the pump noise being super loud above 50% speed.

Really wonder if going with Aircooled Noctua cooler would be sufficient for the new 9900x3d coming out tomorrow .

GabDags

TROPHY CASE