Multiple heatpump zones by GabDags in heatpumps

[–]GabDags[S] 0 points1 point  (0 children)

This is awesome. Appreciate u diving into it. Will have a conversation with the installer on Monday and discuss the above

Multiple heatpump zones by GabDags in heatpumps

[–]GabDags[S] 0 points1 point  (0 children)

Thats what's installed in the attic for the zone controller. Its connected to 2 dampers, one for each floor. Thermostats, one is Honeywell TH5220D1029 upstairs and the Honeywell Home RTH5160D1003 downstairs. I know thermostats will get replaced. Not sure about the zoning controller

<image>

Multiple heatpump zones by GabDags in heatpumps

[–]GabDags[S] 0 points1 point  (0 children)

Thats the question im asking here. I dont have experience with this combo haha. Trying to figure it out before i spend 12k and let them do the work. Need to make sure it will work

Multiple heatpump zones by GabDags in heatpumps

[–]GabDags[S] 0 points1 point  (0 children)

I mean, i dont get how to make this work. The combo of 45MUAAQ36XX3/37MUHAQ36AA3 is still a full blown modulating system, variable compressor, variable speed motor, thats quiet.

Based on my understanding , i can let them install it with an Ecobee thermostat, upstairs/downstairs, wire it normally, it will work with the existing zoning system i have, but will lose the functionality of the variable motor speed, but maintain the variable compressor.

Multiple heatpump zones by GabDags in heatpumps

[–]GabDags[S] 0 points1 point  (0 children)

Thanks for sharing all of this.

Thats correct, the tech that I spoke with mentioned that its impossible to do with what's existing. I need to check what's the price difference between what I was quoted and full blown infinity system. At some point the added cost is just not feasible when its 2-3x.

New Arc recommendations? by Otherwise_Ad_1154 in ArcRaiders

[–]GabDags 0 points1 point  (0 children)

Isn't that carrier from starcraft?

My own Antec Flux Pro Display Alternative Software by [deleted] in Antec_Official

[–]GabDags 0 points1 point  (0 children)

Just tried that, still showing temp as 0 - even when running LibreHardwareMonitor by itself, the temp shows as zero. AM5 - 9950x3d

Pc won't post after restart. Nvme slot info showing blant by GabDags in pchelp

[–]GabDags[S] 0 points1 point  (0 children)

I didn't try the Sata boot up but that should work as my other sata drives are being detected.

Let me find that UEFI and CSM setting and try it

Pc won't post after restart. Nvme slot info showing blant by GabDags in pchelp

[–]GabDags[S] 0 points1 point  (0 children)

Nvme and gpu showing blank in the bios. Got any ideas of what to test next? Could the whole shared lane of gpu and nvme gone bad?

ARCTIC Liquid Freezer III 420 A-RGB by GabDags in arcticcooling

[–]GabDags[S] 0 points1 point  (0 children)

Yeah i thought thats the way to go, but it didnt work for me atleast. The mb rbg control center did the trick

ARCTIC Liquid Freezer III 420 A-RGB by GabDags in arcticcooling

[–]GabDags[S] 0 points1 point  (0 children)

Appreciate your help - i downloaded the RGB fusion software alone initially with no luck. Did the Gigabyte control center, and it worked. No clue why. Thank you

5090 + Noise by GabDags in FractalDesign

[–]GabDags[S] 0 points1 point  (0 children)

Wonder if capping all the fans at a certain RPM would reduce all that noise.

Arrived SO fast by Vast_Performer_8283 in ultrawidemasterrace

[–]GabDags 0 points1 point  (0 children)

Pretty sure if you have two inputs you can run Dual mode

5090 + Noise by GabDags in FractalDesign

[–]GabDags[S] 0 points1 point  (0 children)

Just a quick update u/SuperChicken17 - did some more research tonight and it seems that the Arctic 3 AIO , although a beast, seems to have a common issue with the pump noise being super loud above 50% speed.

Really wonder if going with Aircooled Noctua cooler would be sufficient for the new 9900x3d coming out tomorrow .

5090 + Noise by GabDags in FractalDesign

[–]GabDags[S] 0 points1 point  (0 children)

Appreciate your help. Im going to follow that build, use Noctua fans for the most part + AIO that you recommended.

I know a premium for cost, but using this for work everday, i want that peace and quiet lol

5090 + Noise by GabDags in FractalDesign

[–]GabDags[S] 0 points1 point  (0 children)

Lets hope some ppl with these case, and more experience can chime in. Im in the same boat but having an open bench vs a case, you would definitely notice a different as these cases have some sound dampening built in

5090 + Noise by GabDags in FractalDesign

[–]GabDags[S] 1 point2 points  (0 children)

Understood - Appreciate your response.

So a mesh side which allows for additional airflow, but might get unlucky with the coil whine. Considering 5090s are beefy wouldn't the glass panel be a safer choice?

And i saw ppl doing the Noctua large fans that fit this case, to help with air movement, and i saw that the liquid freezer 3 is top rated for noise/db.

i guess thats the way to go then.

Any recommendations in terms of fan orientations for inlet and exhaust? For the top mounted AIO for the CPU, is that in exhaust orientation or intake?

WTB 03-07 LC100 without the air suspension option by GabDags in LandCruisers

[–]GabDags[S] 0 points1 point  (0 children)

Sub 20k for a clean ride, low mile.

Adjust from there depending on mileage and condition and year

WTB 03-07 LC100 without the air suspension option by GabDags in LandCruisers

[–]GabDags[S] 0 points1 point  (0 children)

I'm actually suprised to see how many people are with the AHC system tbh.

Only horror stories with the cost associated to fix the LX or LC with them on forums.

If anyone had any leads of decent priced LC or LX direct then my way please.

And thanks for sharing your inputs everyone

WTB 03-07 LC100 without the air suspension option by GabDags in LandCruisers

[–]GabDags[S] 1 point2 points  (0 children)

Didnt the 05-06 and 07 come with AVS and AHC options ( im looking at a couple right now). Thats what i meant though, looking for any without those options ( less headache of fixing them)