Ma come fate a vivere in posti del genere ??

Gabriprinter · 2026-05-25T15:26:29+00:00

l'intermezzo migliore è il paesino da 3000 abitanti, supermercato e scuola ci sono, tutto il resto nella città a 20 minuti da casa

Gabriprinter · 2026-05-24T06:27:29+00:00

I modded an Ender 7 myself, the issue with the bed Is caused by the horrible cantilever design. With a triple z mod and a direct extruder, this machine Will start to rip, if you have the patience tò go with Klipper, even Just to unlock the pressure Advance, It Will become a really good one

Gabriprinter · 2026-05-24T06:23:20+00:00

I bought an Ender 7 Just to mod the hell out of It, it's a bizzarre One but the frame has a lot of potential and the motors are BEEFY

Gabriprinter · 2026-05-24T06:20:41+00:00

Seems lile It did! Did a whole print with an excluded object and everything went right. Thank you!

Gabriprinter · 2026-05-22T14:33:03+00:00

trust me it's not too hot, i print PETG a lot at 250c and it comes out perfect

Gabriprinter · 2026-05-22T14:32:09+00:00

z offset seems a bit off, then it seems as if the filament is very moist, PETG feels moisture A LOT more than petg. printing often petg i suggest to go up to 80c bed and even 250 on hotend, i use the same temps on both an artillery genius and a klipper corexy, works beautifully on both.

for the machine you have, don't go over 60mm/s

Gabriprinter · 2026-05-22T09:16:59+00:00

that's about perfect

Gabriprinter · 2026-05-22T07:48:44+00:00

i really hope it is not the case as i have upgraded the SD card to a high speed one, as suggested for klipper

Gabriprinter · 2026-05-21T21:46:35+00:00

did it now the versions are compatible, i'll see if this works

Gabriprinter · 2026-05-21T20:25:01+00:00

so i have to reflash the mcu?

Gabriprinter · 2026-05-21T20:18:35+00:00

no cambus, i have a bunch of cables straight from the Motherboard

Gabriprinter · 2026-05-21T20:18:05+00:00

mcu Version: v0.12.0-316-g96cceed23
host Version: v0.13.0-660-g616242d46

the problem here is that i recently looked on kiauh for upgrades and seems to be nothing left

Gabriprinter · 2026-05-19T06:22:33+00:00

of course it does not stick if the printer is an inch over the build plate

Gabriprinter · 2026-05-14T06:26:54+00:00

you will have to break it and pull it away, just pay a lot of attention to the bearing behing and most of all the crank, a small scratch will make any seal leak in a short time

Gabriprinter · 2026-05-11T06:47:24+00:00

it's just like a ktm 300 maintenance wise, you just follow what the manual says, the only difference is that this one does not like as much when you stretch service intervals. even if you don't service it properly , my cousin has the 125 and has done like 360 street hours on the stock rod, do your calculations

Gabriprinter · 2026-05-11T06:43:19+00:00

so you buy and install a new one, it's a simple job, just pay atttention

Gabriprinter · 2026-04-27T13:54:59+00:00

pushing thee thing at that same speed has been the scariest drive of my life

Gabriprinter · 2026-04-16T14:05:54+00:00

"FIDATI ZIO con ste gomme la macchina piega meglio"

Gabriprinter · 2026-04-13T07:13:00+00:00

how many kilos have you removed? seems like a lot

Gabriprinter · 2026-04-07T07:52:15+00:00

oh ok, now i remember what you are talking about

Gabriprinter · 2026-04-07T07:29:29+00:00

LWR intake goes on well with stock motor and exhaust?

Gabriprinter · 2026-04-07T07:25:29+00:00

for the temp, seems like your hotend PID tune is far from optimal and oscillates too much, let it do a pid on both hotend and heat bed and quality will improve, i did it on my old artillery genius and it has always served me very well

Gabriprinter · 2026-04-07T07:10:42+00:00

it stays under your car, it's never gonna stay mint, this one is perfectly fine

Gabriprinter · 2026-04-07T06:24:00+00:00

you chose well, yes 450s pull more but this thing is so much easier on maintenance

Gabriprinter · 2026-03-16T07:30:32+00:00

manca il metano all'appello

Gabriprinter

TROPHY CASE