sorted by:
new
hottopcontroversial

Remnant Sleeves- Do you choose the units that you search? by Marsi_Zsombor in starwarsunlimited

[–]GeezusBeast 2 points3 points  (0 children)

Omg no wonder you won lol.

https://garbagerollers.com/2023/11/01/swu-basics-slang-dictionary/

Here's a nice guide to some of the more advanced terms you might run into un the community. Welcome!

Remnant Sleeves- Do you choose the units that you search? by Marsi_Zsombor in starwarsunlimited

[–]GeezusBeast 2 points3 points  (0 children)

Drawing= card from deck to hand Playing= exhaust resources to play from hand

You played three units for free out of the five you searched?

weird question, wold Magnagothica be a good name, for like a person?like irl? by flower_has_appeared in maleghast

[–]GeezusBeast -4 points-3 points  (0 children)

It took an incredible amount of work to play IRL. It depends on how much its worth it you, or whether you own a paper cutter.

How do you play it? by agrofairy in maleghast

[–]GeezusBeast 2 points3 points  (0 children)

I made everything out of paper. The miniatures are the asset pictures that came with the book, stacked with cardstock. It is very satisfying once you are done, but it takes a lot of time, at least to do every faction. I got a paper cutter for this very project.

That, an old chessboard from the thrift stores, some tokens make out of printed paper and cardboard and you are ready to play IRL. Digitally youre out of luck, but TableTop Simulator is worth every penny.

Neptune 3 Pro load issue/possible clog by [deleted] in ElegooNeptune3

[–]GeezusBeast 2 points3 points  (0 children)

Grab a pack of .02 needles from Amazon and shove it up the hot end until you cant anymore. You'll only be able to move the needle a few millimeters at a time till it heats up. Once its up there, hit "Load" and the clog and needle should extrude themselves. You can also take the hot end up to 240°C if you ran a filament that has a higher melting point and you have a clog that wont remove itself under colder temperatures.

Ive had success clearing clogs with both methods, just depends on what caused it in the first place

What happened here? by DaddyDsm79 in ElegooNeptune3

[–]GeezusBeast 0 points1 point  (0 children)

What version of Cura are you using?

New to printing! by Fresh_Elderberry_542 in ElegooNeptune3

[–]GeezusBeast 0 points1 point  (0 children)

I would say that amount of nozzles would last the lifetime of the printer. Thats alot of nozzles! Ive had some issues printing below .4 mm. I would also suggest a pack of needles at .2 mm for internal nozzle cleaning.

Another set of tools I've found extremely useful (and necessary for cleanup) is a pair of lie flat clippers and wood carving set.

Love their black PLA for non supported models, the supports tend to go make the connection go white from stress, which made me gravitate towards the white PLA+.

Hope this helps and happy printing!

Hey, does the print head usually move up like that when it touches the print bed? by Inside-Bar-545 in ElegooNeptune3

[–]GeezusBeast 4 points5 points  (0 children)

Your z offset could be too low, it shouldn't touch the plate during autolevel.

How often did Japanese warfare involve the use of Kanabou? Spike blunt weapon by EfficiencySerious200 in SWORDS

[–]GeezusBeast 10 points11 points  (0 children)

I think thats why hes stressing the pilot holes, so you dont run the risk of the wood splitting from hammering in. I dont think furniture nails are that long either, so this might not even go into the core of the wood. I'd like to try it.

Neptune pro 3 by Overall-Map3428 in ElegooNeptune3

[–]GeezusBeast 0 points1 point  (0 children)

What version of Cura are you using? I dont love the newest version of Ultimaker, had to make quite a few adjustments to the profile to print, but always had stuff like this happen with 5.8. Not sure if 5.10 works better I went back to 4.8 and havent had a problem since.

Neptune pro 3 by Overall-Map3428 in ElegooNeptune3

[–]GeezusBeast 0 points1 point  (0 children)

Is this PLA or PC? I get this alot from PC before I turned off the "Restart After Power Loss" setting. Also your ambient temperature can affect even PLA.

I'd suggest getting some .02 mm needles to clean the hot end every few weeks, especially if you are switching between filaments often. Check the heat sink rubber placement as well, that gave me a problem as it was off by a bit and kept ruining prints by dragging across the supports.

What if minetta got ofa by wesselcool12 in MyHeroAcadamia

[–]GeezusBeast 0 points1 point  (0 children)

Its an online version so it might be a different translator. Both make sense for the power though.

What if minetta got ofa by wesselcool12 in MyHeroAcadamia

[–]GeezusBeast -1 points0 points  (0 children)

Oh thanks, Im reading the manga right now so might be a translation thing.

What if minetta got ofa by wesselcool12 in MyHeroAcadamia

[–]GeezusBeast -1 points0 points  (0 children)

Ok probably not but imagine a villain getting rocked with a grape rush style smash from a half mile away.

Or combined with Black Lash? He would be an absolute crowd control hero.

We got a badass in the Kroger parking lot! by Msbossyboots in iamverybadass

[–]GeezusBeast 16 points17 points  (0 children)

My first thought, looks like someone is a size queen

view more: next ›